Horizontal Split Case Pumps Made In China
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1000 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
Horizontal Split Case Pumps Made In China
Application
Single Stage Double Suction Split Case Pump is used for conveying water or the physical and chemical properties similar to water and other liquids suitable for factories, mines, urban water supply, power stations, agricultural irrigation and water conservancy.
Characteristic
Compact structure,beautiful outline,stable operation,low noise;
Both inlet and outlet of this pump are placed under the axial line,so it is unnecessary to remove the inlet and outlet pipeline and motor;
The shaft seal of water pump has fine mechanical seal and soft stuffing seal,which can be selected according to different condition by user;
The impeller is static-balance calibrated,fixed on the shaft with round nut,and its axial position can be adjustedvia the round nut;
The pump is direct drived by motor via resilient coupling,it can be drived by internal combustion engine if it is necessary.
Technical Data
| Capacity | 50-20000m3/h |
| Head | 10-230m |
| Speed | 2900/1450/980/740/580/3500/1750/1180/890/710rpm |
Material
Casing: Cast iron/ ductile cast iron/cast steel/stainless steel/duplex stainless steel
Impeller: Cast iron/ ductile cast iron/brone/stainless steel/duplex stainless steel
Shaft:C-steel/stainless steel
The rotation direction
Viewed from motor, the direction of the pump is anti-clockwise,that is the suction in the left, the discharge in the right.
The rotating direction of the type pump is clockwise, that is the suction in the right, the discharge in the left.
Also can move the driver to another edge according to the user’s requires. Then, the rotating direction, the suction and discharge direction is in the opposite as the described above.
Photo
- Q: Got pump ready and will not pump water. Have tried all things suggested to prime but will not pump water
- You prime the gas with gasoline and the water pump is primed with water. The water pump needs a stop valve in the intake so you can add water and it will not run out. Once the impeller is full and the pump is running it should pump OK.
- Q: Ok, so I have a 1997 3.8 liter ford mustang. I was driving home from work the other day, when temp gauge started to go up. I brought it to mechanic, and he said it was a bad water pump, due to bad antifreeze. So I am getting a new pump, and an antifreeze flush. My question is that since it overheated, will there be any damage to the engine? The temperature gauge never hit the red, and smoke never came out. I had to drive it for approx 15-20 miles when it started to overheat, and the temp gauge was bouncing from hot to normal.
- Depending on how long you overheated your car and how hot it was.
- Q: I have a submersible pump outdoors for the water to my house. Indoors is a holding tank and pressure gauge. It seems the pressure gauge keeps slowly declining down to 20. Then when the toilet is flushed, the gauge kicks on and climbs to 50. Then left alone for a while the gauge again declines to 20. Do I have a leak somewhere? If so , where? Does the ballast inside the holding tank need to be pressurized? If so, how where? I seem to remember years ago, my husband did something with a bicycle tire air pump. Makes sense? Thanks
- If it's going down while nobody is using water then the check valve or foot valve is leaking through when the pump is off. It should pump it to a determined PSI then shut off. I suppose there could be a leak somewhere in the line, but I suspect the check valve. It's pretty common. ....the ballast does need to be pressurized but I doubt that's your problem. If that was bad you would have severe water hammer.
- Q: new switch and new tank
- Sounds like the thermal is cycling. Check it and clean out debris. (overheating)
- Q: where would I be able to find information on how to change out a water pump for that specific type of vehicle and year, as well I had got a stain on the body from road work it seems to be cement how could I take spots out without damaging the body's paint? What are my options thanks...
- why would you like to replace the water pump? seems to me the factory warranty of 3 years 36,000 miles might apply unless you're over on mileage. if you can email me, i will get you the procedure.
- Q: Was able to remove all bolts except the one in the rear of engine one of the bigger bolts the pulley from the serpentine belt blocks itdoes the pulley need to be removed and if yes then how
- Sometimes there are holes in the pulley and you can rotate it until the hole gives you access to the bolt. If there are no such holes, then you will probably have to remove the pulley. The pulley may be fastened with one, four, or zero bolts. If there are bolts for the pulley, remove them and proceed with common sense and use a puller if necessary. If there are zero bolts holding the pulley to the water pump, then it is pressed on and you will need to remove it with a specialty tool called a pulley puller which you can get as a loaner or cheap rental at many auto parts stores. The pulley must also be reinstalled with a pulley installer, also available as a loaner or cheap rental. Are you replacing the water pump or just removing it to do other work? If you look at a new one and it doesn't come with a pulley on it, then you know that the pulley must be removed to go on the new pump no matter what.
- Q: how much would they charge me to change a water pump on my 1999 cadillac deville
- This Site Might Help You. RE: Where is the water pump located on a 1999 cadillac deville? how much would they charge me to change a water pump on my 1999 cadillac deville
- Q: I have a slight idea but I would like to see what steps other people have taken. I have a 1992 ford escort that needs a new water pump, what steps have you taken to replace it?
- It shouldn't in all probability take that long for a water pump. till they are changing the cam belt on the comparable time which could be greater like it. despite the fact that if ?40 an hour is slightly on the steep component. Get a cost from yet another storage or 2 for the comparable interest and see in case you will discover everywhere greater much less high priced
- Q: Hi, I need a 12/24v dc submersible water pump that can pump up to 15m but I can't seem to find it anywhere. Any help would be more than appreciated!
- It's going to be hard to get any DC pump tht can pump 15m (45+ feet). Get and inverter and get a 115v/220v AC pump to do the job. Those are much more plentiful. I know it's more to buy and install, but it is what it is.
- Q: What is the reason that the water supply of pump is getting smaller?
- What kind of pump is it, home pump or factory pump? Single stage impeller or multistage impeller? Vertical or horizontal? Is it single suction or double suction? Different structure of the day pump has different causes of failure. But in general, there are several aspects: 1., the water inlet is small, the inlet pipe is blocked; 2., the blade is worn or broken; 3., the motor speed drops; 4., sealing serious leakage; 5., cavitation phenomenon.
Send your message to us
Horizontal Split Case Pumps Made In China
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1000 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
