SGL Single Stage Single Suction Vertical Centrifugal Pump
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
- Q: I have a 1969 Chrysler with a new 3 core radiator. It still has the stock water pump and I am wondering if a high volume pump would make it run cooler at higher speeds. It runs hotter when you get off the freeway. I have flushed the system and installed a new thermostat. I also replaced the fan clutch. I am at a loss of why it still runs warmer than the 180* thermostat.
- IT is normal for the engne to WANDER AROUND the 180 degree temp! if the engine does NOT BOIL OVER, then things are FINE! COOLANT boils as you know at about 212 degrees, and it may take the COOLING FAN longer to TURN ON! BASICALLY< if the engine does NOT BOIL OVER< then everything is JUST OKAY! USUALLY chrylsers run on the COOL side GOOD LUCK!!
- Q: i changed my fuel pump and now my car wont turn over....any help? maybe starter?
- im confused at everything you are saying here. first off you said you changed the water pump and then it wont start and u said u changed the fuel pump in the next sentence.... so which one did you change?? and how does it try to start but not turn over? if it trys to start the engine has to turn over other wise you would hear a click sound which could be low battery or looose connections... try jumping it. if that doesnt work it could be the starter as well. but generaly if the starter goes out it wont make no noise at all when u turn the key..... if urs makes noise then its trying to turn which means it needs more power... unless you did somthing wrong and the engine is in such a bind it cant turn. now if ur engine is turning over when u try to start it then it could mean its still not getting fuel so u need to check for fuel. if it has fuel then ur problem could resume in no spark to ur plugs which means if u replaced the fuel pump cause it wouldnt start then that may not have been ur problem the whole time u should have checked for spark and fuel before replacing random parts cause u think they are bad. so depending on what your trying to say here its hard to give u a direct answer cause u completely reword yourself over and over and nothing makes sense.
- Q: i installed a new pump don't know how to increase water pressure and to what what pressure it should be set
- This is very simple i would sugest the pressure to be set betwene 60 to 70 NO MORE THAN 70. 1. turn off power to pump (ether the circut breaker or a switch near the pressure switch) you dont want to weld the wrench to the switch. 2. remove the cover to the pressure switch its self (usly one #2 phillips screw) 3. now you will see 4 wires under some sloted screws nearest to the front of the switch, behint that is 1 or 2 bolts with a spring and a nut. 4. if you see 2 bolts you will want to turn the nut on the larger one to the right. you will want to tighten it about 1 to 2 full turns. (the same goes if there is only one bolt also) 5. now open the valve that is on the tank untill you here the switch click. then close the valve. 6. turn the power back on tio the pump and watch the pressure gauge on the tank. i DO NOT RECOMEND MORE THAN 70PSI. 7. if it goes over the pressure you want repete steps above exept loosen the nut in about 1/4 to 1/2 turns untill you reach the desired pressure 8. if it does not reach your desired pressure then you do the same thing exept tighten the nut in 1/4 to 1/2 turns untill you attain your desired pressure. 9. when the pressure is reached, replace cover so you dont risk rusting the contacts. if you need more help feel free to email me. and i will assist you in any way that i can.
- Q: I think the water pump on my 40 hp mercury outboard 2 stroke is not working, the hole witch usually pours out all the water that was used to cool the engine does not pour any water at all. Is this a problem with the water pump? If not what?
- requires visual inspection of the water pump. actually, checking the telltale outlet first might be preferable.
- Q: the outboard runs fine and pumps water out with muffs on but when i put it in the water it doesn't pump any water at all. could it be that the impeller needs replacing? what do you think?thanks
- No question about it. Replace the impeller. It's easy - the hard part is getting the fasteners off without breaking a stud. Be patient and use liquid wrench and give it an hour or more to work. Tap the nuts and then try them. A final resort would be careful (very careful) use of a propane torch to free the nuts. If not replaced, eventually blades will break off the impeller and foul the cooling system.... which can be a very expensive and difficult repair.....overheating is also very bad for the engine.... so fix the water pump.
- Q: i dont think that the water pump is out. i have a 88 evinrude outboard and the other day i noticed that the water was barley trickling out the hose. then it just stopped coming out the hose. it still comes out of the exhaust just fine. the motor is not get hot. is it ok if it still comes out the exhaust/ i will attemp to run a wire up in the hose to see if it is clogged later today. what do yous think
- I think you might want to replace the water pump impeller.
- Q: My '95 Ford Ranger has had the sound of a bearing going bad in a pulley for about two months. Finally this weekend I started it up and it must have locked up, the belt was squealing really loud and snapped. So, now the water pump pulley has rubber chunks on it, which would make me think that is the bad pulley. But the pulley spins perfectly, really smooth. The alternator pulley on the other hand does not spin perfectly. It is not really hard to spin, but it does not spin smoothly. And the alternator pulley is real clean, no rubber on it at all. Any thoughts? I was thinking of buying a cheap belt and putting it on there, have someone start the truck and watch under the hood to see which is bad.
- Bad Alternator Pulley
- Q: I have a 1995 Honda Civic LX 1.5L that needs the water pump and timing belt replaced. What all part do I need to order to replace all of that?
- You need timming belt water pump and water pump silicon the tools for the jobs also. it is not a easy job to do just so you know. Make sure you have a chilton book for the info you need to make sure timming belt is put on right with the cam lined up.
- Q: My dads needs a new water pump for his '83 Silverado v8, anyone have a DIY or a schematic or know of where I can find one? Maybe someone could tell me how. He's pretty handy with cars just doesn't know what needs to come off and in what order. -Thanks in advance!
- ok, this is every little step you could imagine, in detail, with reasons for doing it as said, in the order ive put it down....negligence on my dads part has caused 2 waterpumps to crack in the winter due to lack of antifreeze, because we just put straight water in it, because the radiator is cracked for the same reason as the waterpumps.(but the block luckily hasnt cracked) remove the fan belt, and lower radiator hose, to drain the radiator, and get the belt outta the way. if its a smallblock, you remove the fan shroud, remove the fan and fan clutch, then remove the 3 bolts on the left, and 2 bolts on the right, after youve drained the radiator. once youve removed the 5 bolts, pull it out. wrap a cloth around 1 of the 4 studs on the waterpump, and take a pair of pliers to break it free, repeat untill all 4 are loose. remove the studs, and take the pump with you to autozone so you can get a core charge. scrape the mounting surface clean(dont get anything in the block). install the studs, and have a cloth around any stud your working with when you use the pliers to tighten it down(to avoid damaging the the threads.).apply silicon gasket sealer to both sides of the gasket, and put the gaskets on the block. quickly put the pump back on, and put the top bolts in for support. put the other bolts on, and tighten to about 10ftlbs minimum. slide the fan pulley onto the studs, and put the fan back on. put the nuts back on, and tighten as tight as you can get them, itd be terrible for the fan to go through the radiator. put the fan belt back on, put the lower radiator hose back on, and put the fan shroud back on, in that order. wait an hour for the silicon to dry, and fill the radiator with the motor running, and go for a testdrive
- Q: I have a toyota supra 83 Mechanic said water pump is leaking into engine causing white smoke. He said that hell have to replace water pump nd all gaskets estimated about 500+$ is this accurate? Also water resevoir mysteriously loses water can it be a symptom?
- The water pump may be leaking causing the coolant loss. But it is certainly not leaking into the engine. You may have misunderstood the mechanic's explanation of the problem. Where is the white smoke coming from? The engine compartment? Then the water pump may actually be leaking coolant into the engine compartment and onto the exhaust manifold. If the white smoke is coming out the exhaust, it's not your water pump. Car repairs are more expensive today because they are more complex and shops prey on the lack of knowledge that car owner's have about their cars. You wil be charged for the VALUE of the repair, not the actual COST (plus a reasonable profit) of repair. You'll pay about 2x-3x the retail price of the water pump than you would have paid if you bought the water pump yourself. Without that water pump, your car is junk. My daughter paid $700+ to have a $149 alternator replaced.
Send your message to us
SGL Single Stage Single Suction Vertical Centrifugal Pump
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
