Water Pump Made In China On Sale Good Quality
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Specifications
1)High performance
2)Mechanical seal
3)Cast iron impeller or bronze impeller
4)Lower vibration water pump
5)Large flow
2.Packaging & Delivery
Packaging Detail: | export wooden cases |
Delivery Detail: | within 30 days once receipt of 30% T/T prepayment |
BPO Irrigation Centrifugal Split Water Pump
3.FEATURES
BPO series single-stage double-suction open type centrifugal pump self-researched by the Company after absorbed advanced technology of similar products and combined application requirement of various customers. The series pump adopts excellent hydraulic model, wider type spectrum and better structure. Pump casing is produced by special machine tool, which ensures concentricity among shaft bearing, shaft and pump case, and provides better reliability and maintainability. Apply to municipal water supply and drainage, water circulation of air conditioner, agricultural hydraulic engineering, such as irrigation, drain flooded fields etc., industrial water supply system, firefighting system, water supply and drainage of
heating system, transportation of clean water
4. OPERATING CONDITION
a)Rotate speed: 2950r/min, 1480 r/min, 980 r/min, 730 r/min
b)Flow range: 64.4~9810m3/h
c)Delivery lift: =200m
d)Medium temperature: =80 ,
e)product adopting special materials: -20 ~120
f)Ambient temperature: Lower than 40
g)Operating pressure up to achieves 2.5MPa
5. MATERIAL
a)Pump casing: Cast iron or magnesium iron
b)Pump cover: Cast iron or magnesium iron
c)Impeller: Cast iron, magnesium iron or tin bronze
d)Sealing ring: Cast iron or tin bronze
e)Pump shaft: 45# steel plated with chrome
f)Dynamic and static mechanical sea: Hard carbide, graphite
g)Configuring other material according to requirement is allowable
Rated flow | 10(m3/h) |
Rated head | 26m |
Rated power | 1.5Kw |
Voltage | 220V |
Rated Current | 7.2A |
Rated speed | 2860r/min |
Discharge diameter | 50mm |
6.Conditions of use
Pumps used in the following conditions should be continuously to work properly:
1. For water pumps suitable medium, medium temperature shall not exceed + 40°C
2. The medium PH value between 6.5 ~ 8.5
3. The volume of medium containing solid impurity is less than 0.1%, the size is not more than 0.2 mm
4. The power frequency 50 hz, voltage for single-phase 220 v, 380 v, three-phase voltage fluctuation range for rating of 0.9 to 1.1 times
5. Diving depth of no more than 5 m, is not suitable for irrigation and drainage of sewage and chemicals.
- Q: We have a private well with a 40 year old water pump that is rusting away, and sounds like a truck. It's a double jet well pump sitting on a tank, with a second tank to one side that it's also connected to (with a thick pipe). I don't quite understand why there are two tanks (there's a third which is obviously the hot water). I'm guessing one of these is to hold water, and the other to provide air pressure? In any case, the pump runs OK, it doesn't leak, and provides plenty of pressure. It is just unbelievably loud. I've been told that replacing the bearings might take care of this problem, but seeing how the tank the pump rests upon (with a thin tube connecting it to the pump) is rotting away, and the system is older than I am, should I just replace the whole thing?
- It sounds like you have two pressure tanks. I am going to guess that the one under your pump probably went out and instead of taking it out and re-plumbing everything they just spliced in a new tank. You can get a re-build kit for most pumps but it sound like your pump is pretty old and probably being held together with faith and rust and taking it apart might cause more problems. What I would do is price out what the re-build cost and what labor might be against what a new system might be. If you decide to go with a new system I would suggest looking into getting a submersible pump, using the same tank but making sure it is in a good location and plumbed with a union. when your pressure tank finally goes out it is going to weigh a ton and trying to move it around plumbing can be difficult. good luck and happy holidays.
- Q: I'm planning to install a water pump using electric generator from a very long distance going up from a cliff
- Well yes it wiould , powerful pumps need more electric power so check that the generator can supply the power needed by the pump
- Q: Would a bad water pump make a whinning sound when the engine is reved.....ive checked everything off as to why my car is running so hot and im down to the water pump.....ive put a New thermostat....no leaks anywhere.....no oil in coolant....no coolant in water.....no white smoke.....Fans do turn on.....new colant and i bleed the air out.....but the engine is still running really hot....my car calls for about 13 quarts of coolant but upon refil it took only about 4 quarts...... .. . uld this be signs of my water pump failing.....the pump is not leaking and when i took the housing off the water pump and turn the engine the blades did rotate...but at a higher rpm with the car together i heared weird noies kinda like a whinning sound from the water pump.....1995 Oldsmobile Aurora194,000Northstar 4.0 V8
- the water pump some times whine when it goes out.the radiator could be plugged.when running sqeeze the top hose to make sure its ciculating.this will let you know if its the water pump is out or not.
- Q: I would like to know how difficult it is to change a water pump on my mustang? Is it something I can do by myself? I do know about cars and can perform general maintenance, I am not totally ignorant to whats going on underneath the hood of my car I'm just not sure if I have the tools needed and how difficult it is to do. What tools do I need? Do I need a torque wrench? If anyone can help me out I would appreciate it. Thanks!
- It's not hard, just time consuming. You will need BOTH metric and standard size sockets deep sockets and/or wrenches. For the tensioner pulley you only need 18mm closed-end wrench and you can pull upwards on the tensioner to release tension on the belt. Use a brand new water pump. Do not EVER use a remanufactured water pump. With a new pump you will have a lifetime warranty from any of the popular brand name auto parts stores. For the water pump the battery being disconnected is not required. That is required depending on the car you're working on, but on a 5.0L Mustang it's not. Be sure to stop by Walmart or parts store and pick up a tube of Permatex Blue RTV. Apply a thin bead of RTV on the gasket mating surface then put the gasket on. Don't do this until you're ready to put the pump on. Be sure to use a good scraper to remove old gasket material from the gasket mating surface of the timing cover. DO NOT USE A TORQUE WRENCH ON WATER PUMP BOLTS ON A 5.0L MUSTANG. These bolts are very hard to find now. You only need to snug them at first and then hand tighten them. The factory bolts are notorious for corroding and becoming stuck in the block after their heads snap off. Do not turn the bolts too quickly and be sure to clean them off with a wire brush if they have ANY corrosion and spray them with lubricant before reinserting.
- Q: Where can I get supplies to build water pumps, for decoration.Thank you.
- Home Depot, Lowes, Michael's craft stores, waterfall and water feature stores, Target, WalMart and sometimes Big Lots. I've also found supplies to build decorative water pumps at my local nurseries, Green Thumb and Armstrong.
- Q: The at is a 2003 Toyota celica. And how much would it cost to get the water pump and timing belt replaced?
- You don't have a timing belt on the 1.8L (1ZZ-FE) engine, It has a timing chain! The water pump is driven from the serpentine belt and the labor to replace it calls for 1.8 hours (about $180) and the pump list for $52.99 and it is always wise to replace the thermostat and thermostat O-ring, and that will run you $18.00 and 1 gallon of global coolant $15.00 So your looking at about $280.00 after tax. @ The Interwebz dude, if you like typing so much, why don't you do some clicking so you can do some research before you type!
- Q: how do you change the water pump
- Replacing the water pump requires removing the timing belt because it is timing belt driven, so the timing belt should be changed at the same time. Standard practice is to replace the water pump when the belt is changed to avoid duplicate labor later.
- Q: My water pump is starting to leak. The shops are quoting $250- $300 to replace but I can buy a water pump at the auto parts store and install myself for less than $100 but I don't know what all is involved with this repair or if I should try (my only experience with car repair up to now is recently replacing the alternator). If anyone has done this please let me know what you think. thanks
- you can make it even easier by purchasing a hayne's manual for your car when you buy the water pump. you will need it anyway so you can have the proper torque specs and sequence when reinstalling the new water pump. so if you don't have a torque wrench you will need to rent one. the first step of course will be to drain your cooling system. then use masking tape and a sharpie to number any connectors or hoses you have to remove to access the water pump. once the old one is off make sure to clean every trace of gasket material from the mating flange. then when you are ready to reinstall put a thin coat (use you fingers to spread)of rtv silicone to each side of the new gasket this will help hold in place. then here's where you will need the book insert the bolts and tighten them in sequence shown to the proper torque unless you want to chance cracking the new pump housing. on a car this old if it has not already been done now would be a good time to replace hoses (esp. if they are soft) and your thermostat since you've already got the cooling system drained. once everything is reassembled start the engine and begin pouring in the new coolant, if there are any bleed screws open these it's very important to get all the air out of the system if there are no bleed screws you can leave the cap off the radiator or expansion tank (you'll need to anyway) since one you think its filled when the thermostat opens its all gonna drain down and you'll have to top it off again. here is a good time to pay attention as it approaches normal operating temp be ready to start pouring as soon as the level starts to drop that will help keep more air from getting in. any questions feel free to e-mail me
- Q: think the water pump is behind the crank pulley but im not certain I've pulled apart the front end but I'm having a hard time getting the pulley off so I want to make sure the part im trying to pull off is not the wrong one.
- your water pump is located in the front center of the engine behind the timing cover and is driven by the timing belt. The timing belt must be removed to service the pump and recommend changing the belt at the same time. the only special tool you will need is a puller to remove the crank pulley this can be rented at an auto parts store the rest comes apart with basic hand tools. I recommend buying a service manual for your car at the parts store you get the other items needed to change the pump it will give you a step by step procedure for changing your belt and pump.
- Q: How important is a torque wrench,if so what is the proper fp torque for pump/pulley ?
- dont need to tighten until good and snug torque is critical on head bolts and bearing cap and rod cap bolts etc
Send your message to us
Water Pump Made In China On Sale Good Quality
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
