CHL Horizontal Multistage Centrifugal Water Pump with Good Quality
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1000 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Description
1>Horizontal multistage design with stainless steel stamping welding impeller and diffuser,three different type of choice.
2>Single phase motor up to 2.2kw,Class F and IP55 motor is standard.
3>Standard supply for liquid temperature up to 70 degree centigrade,high temperature pump are available on request.
2. Application
1>cooling water system
2>agriculture
3>domestic water supply
4>general industrial services
5>washing
6>enviroment protection
3. Performance range
capacity: Q up to 32m3/h
head H up to 110 degree centigrade
speed: n 2900rpm or 3500rpm
power: P up to 55kw *2
4. Standard material
All the parts contact with liquid made of 304 stainless steel on request.The pump head and suction & discharge can be made of cast iron on request too.
5. RFQ
1> How can I get trained on CNBM products?
Yes, we provide training courses in our factory (products, general and specific pump technology, hydraulics, and practical applications). Please consult your sales manager or get in touch with our headquarters for more information.
2> Are your pumps cheaper than those of your competitors?
CNBM aims to give its customers the highest standards of quality and service and delivery times, all at a reasonable price.
3> Do you have self-priming pumps?
Yes, our product portfolio also includes two ranges of self-priming pumps: self-priming electric pumps and self-priming side channel pumps.
- Q: I am going to replace the timing belt , tesioner and idler bearing on my 2000 daewoo leganza. I noticed some of the kits have water pumps too. It is likely to break like the timing belt?
- if your going that far to replace the timing belt, sure why not?
- Q: are there any pumps that can save energy more? Environmental protection is necessary and the price is not high.
- Water pump. ( Pond ) Sump pump. ( Flood prevention ) Auto water pump. ( Radiator ) What is the specific purpose of the pump.
- Q: water pump and thermostat were replaced 18 months ago motors done about 20 hrs since replacement have checked and there are no blockagers in water tube what could be the problem thanks
- well, if the water pump isn't pumping water, then the water pump is faulty. only way to know what's wrong with it is to open it up and look at it. one thing you might not be aware of, is that a few seconds of dry running is all it takes to damage the impeller, so if you've been in the habit of starting your motor without supplying water to the lower unit, then that's what happened. Another thing is, the pump sucks in sand and silt, those take a toll on the water pump; the more you run shallow water, the more damage is done.
- Q: belt removal mercury cruiser water pump?
- The pump bracket pivots that allows the belt to be removed. I've seen a few where the alternator belt is over the top of the water pump belt, so you have to remove it first. Actually a pretty easy job.
- Q: What is the defection of water pump
- Anti water hammer phenomenon that is usually said, it is in the high pressure water pump suddenly stops working, the height would hit back phenomenon called defectionThis situation generally occurs in the water pump outlet does not install a check valve, the valve with a check valve has a sound, but the check valve can be a good protection of water pump
- Q: I have a Honda 20003 bf15 d short shaft Ineed to change the water pump I have removed the 5 bolts that hold the lower unit it on but the shifter is steal hooked up how doI unhook that?
- Please get the workshop manual. From an imperfect memory it should be in forward gear to expose a link - but I could be confusing it with other brands. This brand has a known issue with the water pump if ever run dry as both the impellor and the housing can be damaged instantly. The pump should always be replaced as a full assembly, housing, seals and impellor, as detritus can easily block water galleries and that requires extensive work to remediate. The thermostat should be checked and replaced at the same time. Worn and damaged impellor material can easily end up through the block, head, thermostat etc. and that must be checked for as well. The lower cylinder can be down on compression caused by local overheating due to this and mud, sand and corrosion reducing water flow. An engine that very much must be flushed and looked after after all use - that includes all the larger models with this brand. They are quite a good engine, but seem very heavy for the output to me - particularly compared to lifting a two stroke on and off....
- Q: What is the safety head of a pump? Why should a safety head be added?
- Pump selection should pay attention to the following points: (1) to meet the maximum load conditions, should try to reduce the waste of energy; (2) rational use of high efficiency section of the pump; (3) using the same type pump as much as possible, the type of neat, standby each other; (4) to the selection of large pump according to the actual situation, but also should consider taking into account the size, flexible deployment; (5) lack of H value changes, different types of collocation is optional pump operation. (6) to ensure the water conditions, take care of basic level, reduce the pumping depth; (7) consider the standby unit necessary; (8) check the fire with water; (9) considering the development, implementation of the combination of short and long term; (10) to the selection of water pump type local mass production.
- Q: I know that the water pump is belt driven, so it would be easy to connect it to my bicycle. What I am wondering is if I can pedal fast enough to make it work. Does anyone know how fast I would need to pedal to operate the pump?
- Pretty fast. Engines operate at 600-6000 rpm and the pump pulley is a little smaller than the drive pulley, so it is spinning even faster. That said, 600 rpm is plenty fast enough. You can attain that easily by applying pulley to rear tire tread, raising tire off ground and pedaling. To apply bike chain to pulley would give a disappointing water flow.
- Q: Im replacing the water pump in my 1992 toyota celica, and i cant get the pully off! i have been working hard for like an hour, i took the belts off. all i have is good old fashoned sockets and crescent wrenches. do i need to get the pully off? and is it lefty loosey and righty tighty or righty loosy lefty tighty?? because sometimes i hear they reverse it. thanks- jordan
- in case you'll locate the Chilton guide for that vehicle, it ought to have all the tips you opt for to finish that restore. because of each thing going to digital cataloging, many previous severe college save preparation no longer use the Chilton books they have. they frequently carry an complete library of them. see in case you'll get a loose one from the community severe college.
- Q: I'm looking to build a fountain to dispense Wine. For which, I'll need a pump. I'm thinking submersible aquarium pump. I'm concerned about after tastes, and general safety of this venture. Can you drink water that's been run through an aquarium pump?Would alcohol be any different?Is there a better choice? What would it be?
- no dif they only thing is it will get more air which is a good thing for wine
Send your message to us
CHL Horizontal Multistage Centrifugal Water Pump with Good Quality
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1000 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
