QW Series Submersible Sewage Cutter Pump Sewage Pump
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1000 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
WQ Submersible Sewage Cutter Pump Sewage Pump
Application
This series pump is widely used for sewage treatment of city construction discharge for architecture projects, hotel, mine, pond, dyeing and printing, paper making and textile industries.
It is the ideal tool for transportation of sludge, slurry, living sewage, feces and stale wastes, solid grains fiber, paper chips, sandy soil etc.
Model Description
100WQ 50-30-5
100: Drain aperture (mm)
WQ: Submersible sewage pump
50: Capacity (m3/hr)
30: Head (m)
5: Power (kW)
Operations Conditions
1. The medium temperature should not be over 60oC, the density 1200Kg/m3, and the pH value within 5-9.
2. During running, the pump must not be lower than the permitted lowest liquid level.
3. Rated voltage 380 V, rated frequency 50 Hz. The motor can run successfully, only under the condition the deviations of both rated voltage and frequency are not over ± 5%.
4. The maximum diameter of the solid grain going through the pump has not to be larger than 50% of that of the pump outlet.
Picture
Why choose us
High Quality
1.Exported to 58 Countries
2. More than 90% customers make payment before meeting us!
3. Reorder rate up to 80%
4. Never sell any renewed pumps
5. Focus on middle and high-end market,we never seize market by using inferior material
FAQ
1. How to get our quotation in time, pls answer following questions:
1)What liquid do you transfer?oil ,food or corrosive chemical liquid,with solid particle or not and so on
2) What's the flow or capcity (m3/h, L/m)?
3) What's the discharge head (m, feet, Mpa, bar )
If you do not have any request, we will do as our normal standard.
4) Contact us by under business card information
2.OEM: Ok
3. MOQ: 1set
4. Package: Standard export wooden case(also according to your requirements)
5. Shipping ways: By sea, By air, By express
6. Lead time: 3-15days
7. Warranty Period: One year, except spare parts
- Q: What is the function of the pump?
- Drainage or irrigation
- Q: I've got a 1997 Ford Probe, taken it to a couple different places; whenever I drive my vehicle, it tends to want to overheat. I don't drive it to the point where it does though, I know that could cause more damage! I've noticed that when I go out to my car in the morning, there's some coolant on the ground by the front passenger's tire. Before I drive it I fill it with coolant, as to try to keep it from overheating while driving.I've been told that it's the water pump leaking from 2 people but then the last person said there's no leakage. I'm wondering if it might be something else? Maybe a thermostat, a hose, maybe? How would I figure this out???
- Sounds like it's probably the water pump to me too. It's easy to tell though, just get it on a lift and take a look at the water pump. If it's leaking out of the weeping hole, it's toast. Don't power wash an engine unless you want to risk very expensive repairs from water being forced into places it's not supposed to be. Odds of the pump locking up and leaving you stranded before those bearings get VERY upset, start screaming and dumping fluid like there's a hole in the system is a hundred to one. You should be able to limp it to a shop just fine when it gets worse. Just be careful not to overheat and you'll be fine. (I did say 1 in a hundred, you're not super unlucky, are you?)
- Q: What's the water pump?
- Cooling water pumpDetermination of water replenishing pump1) the hourly flow is 4%~5% and the total water quantity is.2) the lift is the replenishment point and the pressure is plus 30~50 kPa.3] water pump to overcome the pressure of the replenishment point and the pressure difference between the make-up water tank, during which the pipeline is not long, you can ignore its resistance4) open system replenishment, no replenishment pump
- Q: i started backing out of my garage and something sounded like it poped then lots of steam started coming out and water was on the ground on the right side of the car non on the left and the water pump needle in my car is all the way to the red can some one help me
- your car was almost out of water t overheated and blew a hose. You need to find out what is leaking the coolant out and fix it. You did not mention the year make or model so there is little we can advise. Many cars have a weep hole on the botton of the water pump and when the seal breaks this is usually because the bearing in the water pump is worn. Put in a new pump and inspect all heater hoses and radiator hoses replace the thermostat and then add coolant. Be sure to open the heater core so no air bubbles block the system.. leave the radiator cap off and let the car warm up good so the thermostat opens and coolant starts to curculate rev the enging slowly several times to work out any air fill the system (replace radiator cap with a new one too) put new cap on and drive around for about ten minutes and park the car. Let it cool so that any coolant needed gets sucked in through the pressure cap. Refill overflow bottle as necessary.
- Q: I currently have a gould 1/3 horse jet water pump and a rusted pressure tank that I would like to replace. There are two bathrooms, both with showers, 2 bathroom sinks and the kitchen sink, as well as the washer. What horse power should I have for 5 faucets and what size pressure tank would be sufficient? The shower in the upstairs bathroom hardly has pressure at all with the current pump and pressure tank. Any help would be greatly appreciated. Thank you in advance.
- I would go with a ? hp jet pump which normally come with a 30-50 pressure switch Check out Home Depot I believe they sell the Flotec. which will run about 260.00. It will give you much better pressure upstairs and if you want to increase the pressure you can chance the pressure switch (24.00) to a 40-60. As for tanks I would look at the 42 gallon. If you have any more questions about tanks and pumps…feel free to e-mail me
- Q: I am looking for foot peddals and one of those pumps that you can use to pump excess water out of the cockpit..... any Ideas where to look for the cheapest of both...I checked Dunhams and *****.
- you might check mountain sports in arlington,texas they are good t
- Q: Cant get the bolt loose fromthe fan that is attached to the water pump in my ford ranger. need to remove bolt in order to remove water pump.
- you're taking a wrench which will greater healthful at the back of the fan, and knock with a hammer on the wrench to interrupt the nut loose. you turn the nut to loosen it an identical way the fan turns while the engine is working
- Q: What do I get to bring a portAble water conection? Like as in bring a hose with you I gess? It's confusing how I described it but I just wanna use a garden hose so I can wash cars from my truck. Sorry it's hard to describe
- A portable water pump. They come in a variety of sizes depending on your needs. A friend of mine runs a window cleaning service from the back of his truck. I don't know what size pump he has but I do know he also has a permanent water tank fitted as well as all the other fittings accoutrements for the job.
- Q: Level 200 meters distance, elevation 30 meters, how much lift water pump?
- Lift is usually used to overcome vertical height and pipe loss. Now you can determine the vertical height of 30 meters, 230 meters long pipeline losses but you lack of data not calculated. With the following conditions can be calculated: 1, flow; 2, pipe diameter; 3; pipeline material; 4, elbow number; 5, valve types and quantities.
- Q: I have gotten oil in my coolant, and coolant in my oil..It might be the head gasket, no doubt, but many people said (online forums) that my bike, has issues with the seal that is separating oil pump from water pump. They go bad, and when they do, the oil mixes with coolant and vise versa. Now, I am seeking from professional help, on how to take out both of the pumps, without messing up timing, and also without messing up anything else. I have removed the entire exhaust system, dropped the oil pan, and i can see the oil/water pump pretty good. What i do not know is how to remove it properly. Any help is help, I have searched and searched on google and forums on how to perform this task, but couldnt find any specific help on how to remove the pump. Thank you!!!!!
- Most okorder for a good schematic of your oil pump and water pump assembly
Send your message to us
QW Series Submersible Sewage Cutter Pump Sewage Pump
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1000 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
