Water Pump Centrifugal Good Quality Made In China
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Specifications
1)High performance
2)Mechanical seal
3)Cast iron impeller or bronze impeller
4)Lower vibration water pump
5)Large flow
2.Packaging & Delivery
Packaging Detail: | export wooden cases |
Delivery Detail: | within 30 days once receipt of 30% T/T prepayment |
BPO Irrigation Centrifugal Split Water Pump
3.FEATURES
BPO series single-stage double-suction open type centrifugal pump self-researched by the Company after absorbed advanced technology of similar products and combined application requirement of various customers. The series pump adopts excellent hydraulic model, wider type spectrum and better structure. Pump casing is produced by special machine tool, which ensures concentricity among shaft bearing, shaft and pump case, and provides better reliability and maintainability. Apply to municipal water supply and drainage, water circulation of air conditioner, agricultural hydraulic engineering, such as irrigation, drain flooded fields etc., industrial water supply system, firefighting system, water supply and drainage of
heating system, transportation of clean water
4. OPERATING CONDITION
a)Rotate speed: 2950r/min, 1480 r/min, 980 r/min, 730 r/min
b)Flow range: 64.4~9810m3/h
c)Delivery lift: =200m
d)Medium temperature: =80 ,
e)product adopting special materials: -20 ~120
f)Ambient temperature: Lower than 40
g)Operating pressure up to achieves 2.5MPa
5. MATERIAL
a)Pump casing: Cast iron or magnesium iron
b)Pump cover: Cast iron or magnesium iron
c)Impeller: Cast iron, magnesium iron or tin bronze
d)Sealing ring: Cast iron or tin bronze
e)Pump shaft: 45# steel plated with chrome
f)Dynamic and static mechanical sea: Hard carbide, graphite
g)Configuring other material according to requirement is allowable
Rated flow | 10(m3/h) |
Rated head | 26m |
Rated power | 1.5Kw |
Voltage | 220V |
Rated Current | 7.2A |
Rated speed | 2860r/min |
Discharge diameter | 50mm |
6.Conditions of use
Pumps used in the following conditions should be continuously to work properly:
1. For water pumps suitable medium, medium temperature shall not exceed + 40°C
2. The medium PH value between 6.5 ~ 8.5
3. The volume of medium containing solid impurity is less than 0.1%, the size is not more than 0.2 mm
4. The power frequency 50 hz, voltage for single-phase 220 v, 380 v, three-phase voltage fluctuation range for rating of 0.9 to 1.1 times
5. Diving depth of no more than 5 m, is not suitable for irrigation and drainage of sewage and chemicals.
- Q: I replaced the water pump on my 1997 acura cl 3.0 v6 vtec. I set the timing how alldata said to. (Lined up marks on timing drive pulley and both cam pulleys) and put it all back together. Now when I start it the motor runs rough for about 45 seconds then it smooths out but won't rev past 3000 rpm. What are some possibilites it could be?
- reset the ecu, by disconnecting the battery cables off the battery for 30 mins and then reconnect them and see what happens
- Q: I switched on the pump and smoke came out of it, i opened the pump n found it had some water probably caused the shock. How to repair it or is it dead?? ** its not a well pump just a normal one that pump the water to the tank from a small reserve
- If you have to ask the question you don't have the skills to do it. You could see if there's anyone in your area who rebuilds motors and ask them to look at it, but if it smoked it's probably dead. If you want to try some simple things, take it apart, dry it out and put it back together and see if it works. If does, see if you can see where the water was leaking from and see if you can seal it back up.
- Q: There is no water at all! What can we do to troubleshoot this before calling a Plumber? This is the first time this has happened and we never had a well before. Please help (serious answers only)
- It's not your water heater. It's not the thermostat. Check that the circuit breaker or fuse to the well is not off or tripped. (If it is a circuit breaker, turn it all the way off firmly and then back on.) If it was tripped, it probably tripped for a reason and you'll eventually have to find the reason. If the circuit breaker is not tripped and/or fuses aren't blown, there may be a problem with the pressure switch which is the device that turns the pump on and off in response to water pressure. Not something amateurs should fool around with.
- Q: When using a frequency converter to adjust the pump, what is the relationship between the change of the speed and the efficiency of the pump?
- First, the wind pumps such load is usually called square torque load, which is in a certain range of speed and torque is roughly proportional to the square of the speed of N, TL=kn^2, power and speed is proportional to the cube, the energy-saving effect is obvious. Can also be described according to what you pump model, the pump is divided into piston pumps, screw pumps, impeller pumps and centrifugal pumps.Secondly, under the standard condition, the higher the efficiency of the centrifugal pump, the higher the speed determines the size of the centrifugal force, the higher the speed, the greater the centrifugal force, and vice versa. Plunger pump and screw pump is not the same, the speed of speed and efficiency basically no impact. Third, in addition to buying the pump, you can let the manufacturer give you an FM curve, so you can see the frequency of mediation when the water pump efficiency changes
- Q: the outboard runs fine and pumps water out with muffs on but when i put it in the water it doesn't pump any water at all. could it be that the impeller needs replacing? what do you think?thanks
- Replacing okorder /
- Q: I currently have a gould 1/3 horse jet water pump and a rusted pressure tank that I would like to replace. There are two bathrooms, both with showers, 2 bathroom sinks and the kitchen sink, as well as the washer. What horse power should I have for 5 faucets and what size pressure tank would be sufficient? The shower in the upstairs bathroom hardly has pressure at all with the current pump and pressure tank. Any help would be greatly appreciated. Thank you in advance.
- I would go with a ? hp jet pump which normally come with a 30-50 pressure switch Check out Home Depot I believe they sell the Flotec. which will run about 260.00. It will give you much better pressure upstairs and if you want to increase the pressure you can chance the pressure switch (24.00) to a 40-60. As for tanks I would look at the 42 gallon. If you have any more questions about tanks and pumps…feel free to e-mail me
- Q: honda acord water pump 1988
- hello Purchase a how to book, because part of the water pump sits behind the timing belt cover.Hope this was some help.
- Q: I was wondering how to replace the water pump in a 94 Plymouth Voyager. Its my moms van and she is scared that they are going to have to pull the motor to get to the water pump to replace it. I dont know so i am hoping one of yall wonderful people do. along with your answers can you give me an estimate of how much it will cost to fix? Please!!!
- No need to pull the engine. It's accessed through the wheel well. Best to have a shop perform the work, as it's probably past due for the timing belt to be replaced. Replacing the water pump requires removing the timing belt.
- Q: I have a 1978 El Camino V8 305. My power steering has been going out on me, and since then my belt has been squeaking usually when it first starts up. This morning when I got to work, smoke was bellowing from under my hood. Im trying to troubleshoot. Is it possible that my power steering pump damaged the belt enough that the water pump went out?
- If the power steering pump was dragging, you probably lost the belt, so the water pump was not working and the engine overheated. Water pump is probably OK. Replace the belt and fix or replace the power steering pump.
- Q: Here is the deal...*Van over heats*Blows Cold quot;heatquot;*Coolant leaks (not into the oil)*Added coolant and water (nothing happened)*Started van, felt the hoses (no h2o flowing thru)Ive had this problem for a while. Some times my van drives just fine and heats just fine, then some days it wants to over heat and blow cool quot;heatquot;. Adding coolant to my van used to do the trick, but now its not working. If it is my thermostat that is broke, the water/coolant would still run through the hoses right?I really think its my water pump out, but I am not sure. Does this sound like my water pump? If so, I plan on changing it myself, how do i find step by step instructions to do so.... I have never done it before, but I cant afford to take it to a mechanic! Thanks for your help!
- Again, see last answer to your same question. You obviously dont know what the real problem is, could be water pump and might not be. Instead of wasting over 25.00 on a water pump and that not being the problem, why dont you take it to a reputable repair facility and have the cooling system analyzed and they can tell you EXACTLY what part(s) need replacing, then go from there. Nobody can diagnose your cooling system problem over the internet since we are not at your vehicle with a coolant pressure tester and block test tool.
Send your message to us
Water Pump Centrifugal Good Quality Made In China
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
