Standard Hot Dipped Galvanized Iron Wires

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Commercial Galvanized Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

(7) Zinc Coating

Meet GB/T 15393 standard.

Q: would the wiring harness on a 1.8 acura integra engine fit a 1.6 honda civic harness?: i've got not got the coolest comparable form jeep, even even with the shown fact that it particularly is terrific to attempt the wreckers, they continuously have spare areas, in the event that they have not got it, then ring Jeep up and ask them in the event that they have a spare one, there low fee.

Q: A long horizontal wire carries a current of = 52 . A second wire, made of 1.00--diameter copper wire and parallel to the first, is kept in suspension magnetically 5.0 below.What is the magnitude of the current in the lower wire?: The lower wire is kept in suspension magnetically means that the downward force of gravity is equal to the upward magnetic force. Its NOT an easy problem so we need to solve it in small steps. Let's find the two forces acting on the lower wire: (*) Downward force of gravity = mg = (volume) x (density) x (gravitational acceleration) = (pi r^2 L) x(8920)x(9.8) = 0.06896L We assume the radius of the wire is 0.5 mm or 0.0005m, copper density is 8960 N/m^3, gravitational acceleration = 9.8 m/s^2 (**) Upward magnetic force = mu(zero) x i(one) x i(two) x L / (2 pi d) = 2.08x10^(-4) L i(two) mu(zero) is a constant = 4 pi 10^(-7), i(one) is the current in the first wire = 52A, i(two) is the unknown current in the second wire, d is the distance between the wires = 5 mm or 0.005m The forces are equal, therefore 0.06896L = 2.08x10^(-4) L i(two) We divide both sides by L (the unknown length of the lower wire) and now we can solve for the current i(two) ANSWER: i(two) = 331.5 A

Q: I recently re-wired my house with 4 wire telephone wire. They all meet in the attic. How do I wire them together and is there some kind of junction plate I can use? Additionally, I did also wire my house with Cat6 wire, but would like to keep it strictly for Internet.: (links just for reference, from search engine results)

Q: I have 2 connectionswire and wireless,im only connected to my wire how do I open a connection to my wireless?: You'd need a wireless router 1. Start Menu 2 .Connect to Go into wireless connections I.E. if your computer doesn't find the router that the wireless is hooked up to- than you need a WIRELESS ROUTER to do so.

Q: lime wire: drag and drop stuff to itunes, make a playlist with the songs, put disk in.. and press burn.. :)

Q: A load of 125 kip is being held by 3 wires all going up. The Wire one goes straight from the load to the horizontal. Wire 2 and 3 form a V on top of wire 1 and are 30 degrees from wire 1. This is a 2-D problem.: You need to use summation of forces. Wires 1 and 2 are gonna have the same tension on them, just in opposite directions. so in the x direction, Fx=125cos(30)+125cos(150) (the vertical wire doesn't contribute to the x-direction forces and I choose 150 because the wire on the left really has an angle of 180-30 or 150) in the y direction, Fy=125sin(30)+125sin(150)+125sin(90) (The vertical wire is a 90 degree angle) Tension=sqrt( Fx^2 + Fy^2 )

Q: I recently purchased a used car already wired for an amplifier, however, when I looked at the wiring i found that the installer ran 8 gauge wire and then crimped it to a 12 gauge wire (with fuse) that connected to the battery is this bad? should i change it to 8 gauge? Or does it not matter?: you okorder /... you can pull 20 amps 6.6 feet but you can not pull 25 amps any distance so if your amplifier has two 15 amp fuses in it, you will need to swap out the 12ga section for 8ga.

Q: I need to wire a single 120v outlet from the 240v volt wire I use on my compressor. Im installing a 120v electric automatic drain valve on my large shop air compressor. The compressor is wired up with SJ00W 10-AWG, 4-wire power cable (red,green,black white wires). and is rated at 240v @ 15-amp(compressor not wire). The drain valve uses a normal house hold current wiring config. (black,white and open copper)The 240v power supply is the only supply I have near by, (two of them actually) Or I would just wire the automatic valve off an outlet and call it a day. So How do I wire a 120v 3-wire set up from the 240v 4-wire supply? Thanks: How To Wire 240v

Q: My house is currently wired using Cat-5 lines. If I were to replace the Cat-5 wiring with Cat-6 wiring, would I see an increase in my DSL speed?: Short answer is no. The reason is Cat-X is category then a number, the number meaning twists per inch. The twists help keep out crosstalk and interference. Rarely an issue in most households and even reasonably sized businesses.

Q: And i am unsure on how to wire the speakers. Do i just splice the wires from the speakers to the corresponding wires on the harness. P.S. It is not actually in a boat, it will be connected to a 12v battery.: U JUST RUN THE HOT(RED) WIRE TO THE BATTERY. U ALSO MIGHT HAVE TO HOOK UP THE MEMORY WIRE(YELLOW WIRE) AND THE REMOTE ( SOLID BLUE) WIRE TO THE POSITIVE TERMINAL OF THE BATTERY AS WELL BEACAUSE SOME RADIOS WONT TURN ON WITHOUT THESE WIRES COONECTED. THE WHITE AND GREY WIRES ARE THE FRONT AND THE GREEN AND PURPLE ARE THE BACK SPEAKERS. YOU SHOULD GET THE WIRING HARNESS FOR THE WIRING IF ITS GOING IN A CAR LIKE A JEEP THEN ALL U GOTTA DO IS MATCH THE COLORS UP ITS EASY . BUT STRAIGHT TO A BATTERY DO IT THAT WAY JUST MAKE SURE U HAVE A GOOD GROUND.

Send your message to us

*Email

*TEL

*Quantity

*Unit