Horizontal Multistage Centrifugal Pump Made In China
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 1000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Horizontal Multistage Centrifugal Pump with Lowest Price
CHL, CHLK and CHLF (T) type pump are mainly used in industrial field:
A. Air-conditioning system
B. Cooling system
C. Industrial cleaning
D. Water treatment (Water purification)
E. Aquiculture
F. Fertilizing/metering system
G. Environmental application
H. Other special applications
Curve conditions:
Following conditions are suitable for the performance curves shown above:
*All curves are based on the measured values of 50Hz: constant motor speed 3500r/min;
*Curves tolerance in conformity with CE;
*Measurement is done with 20 ℃ are-free water, kinematic viscosity of 1mm ² /sec;
*The operation of pump shall refer to the performance region described by the thickened curve to prevent overheating due to too small flow rate or overload of motor due to too large flow rate.
Motor
A. TEFC motor 2-pole
B. Protection class: IP 55
C. Insulation class: F
D. Standard voltage,
50 Hz: 1*220-240V
3*220-240V/380-415V
60Hz: 1*220-240V
3*220-240V/380-415V
E. Single phase motor (max): 2.4kW
Operation condition
A. Liquid temperature:
Normal temperature: -15oC~+70oC; Hot water type: -15oC~+110oC
B. Ambient temperature: Up to +40oC
C. Max. Operation pressure: 10 bar
D. Max. Inlet pressure is limited by max. Operation pressure.
Model | CHL2 | CHL4 | CHL8 | CHL16 | CHL8 | CHL16 |
Rated flow(m 3 /h) | 2 | 4 | 8 | 16 | 8 | 16 |
Flow range(m 3 /h) | 1~3.5 | 1.5~8 | 5~12 | 8~22 | 5~12 | 8~22 |
Max pressure(bar) | 5.5 | 4 | 5 | 4 | 5 | 4 |
Motor power(kw) | 0.37~0.75 | 0.37~0.75 | 0.75~2.2 | 2.2~3 | 0.75~2.2 | 2.2~3 |
Temperature range( o C) | -15~+110 | |||||
Max efficiency(%) | 46 | 59 | 64 | 70 | 64 | 70 |
Outlet | G1 | G1.25 | G2 | G2 | G1.5 | G1.5 |
Inlet | G1 | G1 | G2 | G2 | G1.25 | G1.25 |
- Q: What is called soft start of water pump?
- Soft start is a form of electronic control, mainly through the soft drive to achieve. Principle: the former contactor is directly started as contactor, first pull in, and the device is started by soft driving. Soft start device start smoothly, starting current is small, control system life is long. Soft start is now in widespread use. But the use of high-power equipment is less, the general current is less than 120A.
- Q: I have a 2005 Impala and it has been acting funny. Some morning the heat takes about 20 minutes to start working. The air conditoner has not came on once. The gage also takes awhile to start working and when it does it goes pass the halfway mark.I even notice when im sitting at a red light, i can feel the engine shaking a little. I have a appt to get it check and put on the machine tomorrow. I just want to go there with an idea of what the problem could be. Could this be a thermostat or water pump problem???? Help?
- Sounds like the thermostat is sticking,
- Q: What are some good brands of aquarium water pumps? I have had bad experiances with Hydor Seltz (cheapest ones I could find, ugg, I know, you get what you pay for) pumps, failing very quickly, and sounding like plastic gears grinding around inside. What is the best kind to get?I need one that's around 150gph
- PowerHead? or Sump Pump? I have used hagen aquaclear powerheads on my saltwater tanks for years 24/7 without a problem. I just purchased 3 MaxiJet 1200 powerheads and a wave timer to see haw they do, 6 months now 24/7 and so far so good. The longest lasting Sump Pump that I have ever owned is made by Ehime, I've had it for 14 years now and it's still going in one of my tanks. I better cross my fingers on that one.LOL
- Q: Okay so earlier, I went to go test out my water pump and all on my 66 mustang 302. And I got it up to normal operating temp, and had the rad cap off. I gave it some gas, the coolant level didn't go down, instead it came out the rad pretty badly. I've been having overheating problems, and I have no leaks, i just replaced the thermostat a few days ago, it didn't help. I haven't seen any leaks around the weep hole on the water pump, or noises. Other than a belt that does need to be tightened a bit, you can hear the belt squeling a tiny bit. So do yall think it could be my water pump?
- there are several problems that can cause this one is a stoped up radiator or a lower radiator hose thats soft
- Q: belt removal mercury cruiser water pump?
- The pump bracket pivots that allows the belt to be removed. I've seen a few where the alternator belt is over the top of the water pump belt, so you have to remove it first. Actually a pretty easy job.
- Q: I'm just wondering where I should buy my new water pump for my 2.2 cavalier? Auto zone, carquest, checker? Does it matter which one?Thanks
- out of all the auto parts stores i use autozone is the cheapest but 45 miles away so i mainly use napa.
- Q: How do I replace the water pump on a 1996 Mercury 200 hp outboard engine? I have the parts, but want to make sure I replace it correctly. Thanks!
- good answers. forward gear is a good idea, just make sure the controller is in fwd. also. when you turn the driveshaft to put the housing over the impeller make sure to always turn it clockwise from the top.
- Q: quot;A tank has the shape of an inverted circular cone (point at the bottom) with height 10 feet and radius 4 feet. The tank is full of water. We pump out water (to a pipe at the top of the tank) until the water level is 5 feet from the bottom. The work W required to do this is given byquot;I know how to find it if it's a right circular cylinder, but how do I adjust for the changing area? Also would a and b = 0 and 5? Thanks ahead of time!
- calculate the amount of water U start with by computing volume of cone: V = 1/3πr?h {r = 4', h = 10'} V = 0.333π(4)?(10) = 167.55 ft? calculate the amount of water remaining in cone after pumping is done: V = 0.333π(2)?(5) = 20.944 ft? calculate the volume of water pumped: 167.55 - 20.944 = 146.6 ft? 1 ft? of water weighs 62.4 lb, calculate weight of water removed: 146.6(62.4) = 9148 lbs The Center of Mass of the water in the cone (when h = 10') is at 1/4 of 10 ft = 2.5 ft high The Center of Mass of the water in the cone (when h = 5') is at 1/4 of 5 ft = 1.25 ft height The Center of C.of M. change = 1.25 + (2.5 - 1.25)/2 = 1.25+0.625 = 1.875 ft If we consider that the Center of Mass of the water removed was at 1.875 ft, All the water removed was then lifted an average of 10 - 1.875 = 8.125 ft Work done = W = (9148)(8.125) = 74,300 ft-lbs ANS
- Q: I have a 2000 chevy impala with 85K on it. I have heard/a weird rattle noise from under the hood for some time now. I once asked about it on here and got suggestions regarding front end problems. I had that checked out and the front end is good. I still have the rattle noise along with a high pitched, but not very loud, squeeling noise when I accelerate. I am leaking coolant and it seems to be coming from near one of the belts. Is this a bad water pump? If so how expensive of a fix is it and how involved of a repair is it?
- It sounds like a water pump or maybe a loose connection. It is probably time for a water pump if it hasn't been replaced yet. Parts will run under $60 and it probably involves an hour of labor. The Impala is a big car, it shouldn't be hard to get to and remove. Taking it to a shop will run under $100-$150 for everything.
- Q: I would like to make a simple electric pump that can pump water. I would like to know how it works. I would be most thankful if you can provide me a link of an animated video on how motor works.
- Pump And Motor Works
Send your message to us
Horizontal Multistage Centrifugal Pump Made In China
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 1000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
