miniature diaphragm pump
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
- Q: Fire pump and spray pump requires a preparation, 2 sets of the same pump requires mutual investment, when the main pump failure of backup pump automatically put into use. 1: so what is the throwing device: 2: where is the device installed? It should be in the water pump control box. 3: what is the principle of mutual voting? Detailed description
- You can refer to the DCL and DCS microcomputer access control system, you can achieve the purpose of remote control. Specific installation methods can be found in local instrument engineering inquiries.
- Q: The water is being put in because it was overheating. We changed the thermostat and everything and it got better, but about a month later it started overheating again and now it is leaking water bad from underneath the car. Whatever is leaking is covered by a shield thing. Im not sure what it is, and I dont want to replace it before I know if thats really what it is. Any help would be greatly appreciated.
- If the leak is on the passenger side of the car (near the tire) then it is most likely your water pump. It is driven by the serpentine belt that drives most of the visible components on the passenger side of the engine. (power steering, A/C, Alternator etc) To check it, you need to look UNDER the water pump, it has a weep hole. If this small (1/8) hole is wet, or shows signs of having been leaking (like discoloration or rust) then your waterpump seals or bearings are going. The unit must be replaced. This should also fix your over heating problems. If the leak is near the back-center of the engine, then it may be a frost plug (also called a freeze plug) these are designed to pop if the enging coolant freezes to prevent damage to the engine block, they can also be opened if the engine over heats. Be careful when replacing this plug, if you drive it INTO the engine, you will have to dismantle the engine to get it out again. On the plus side, you can get rubber plugs that are easy to install and quite inexpensive. I'd place the water pump as the most likely problem.
- Q: What are the conditions for the series and parallel connection of the pumps?
- Parallel pumps: the pump is required to lift the same. This effect is to increase traffic.Pumps in series: requirements are similar to the flow of water pumps. This allows you to increase the total head and recommend adding small pressure tanks during the series connection.
- Q: Ok, so I have a 1997 3.8 liter ford mustang. I was driving home from work the other day, when temp gauge started to go up. I brought it to mechanic, and he said it was a bad water pump, due to bad antifreeze. So I am getting a new pump, and an antifreeze flush. My question is that since it overheated, will there be any damage to the engine? The temperature gauge never hit the red, and smoke never came out. I had to drive it for approx 15-20 miles when it started to overheat, and the temp gauge was bouncing from hot to normal.
- The temp gauge prob bounced from hot and normal because the water pump worked intermittently and if you didnt drive the car in the red zone and was working when you brought it to the mechanic theres nothing wrong with it
- Q: replaced water pump and thermostat, flushed, opened bleeder valve had long life red colored original coolant, no visible leaks obstruction, when became hot on highway, accelerated quickly and temp back down to norm, eventually after 3hrs driving o.heated stopped and got towed home, new water pumps fins/pulley not turning as freely as old one, no leak out of inspection hole, hoses good shape.2001 2.2l ohv sunfire, air cond.
- Check the bearings on the pulley / pack some grease in there. Hope some help !
- Q: Water dispenser in refrigerator has stopped working, how do I replace pump?
- There is no pump in the fridge. Water is propelled by pressure before it gets to the fridge.
- Q: Where can I get supplies to build water pumps, for decoration.Thank you.
- Home Depot, Lowes, Michael's craft stores, waterfall and water feature stores, Target, WalMart and sometimes Big Lots. I've also found supplies to build decorative water pumps at my local nurseries, Green Thumb and Armstrong.
- Q: What does the lift of a pump mean?
- Lift lift height = water raise height = total lift lift height + water = water is expressed in M by H (m)
- Q: Hello, I'm having an issue with grinding/metallic noise from engine bay. Alternator was replaced today and didn't fix. However, when I got the car back from the garage the oil level indicator is saying quot;inactivequot;. I seem to find some answers on the web that say the oil level indicator is in some way connected to the water pump. Car has 95k miles on and I doubt it had been changed. Could this be the cause of the noise? And could anyone possibly tell me which pulley it is on the belt? Many thanks for your time :)
- Alternator replaced? Will you be getting credit back for that? Anyway, at 95k it's almost about time to do a full preventive maintenance thing. That includes the water pump, belts, radiator hoses, I would do the tensioner and idle pulley too since one is there already. Would replace the radiator expansion tank too. Change the spark plug and valve cover gasket too while you are at it. The spark plug can be done separately, but it's time to replace them.
- Q: I would like to know that a water pump or water motor which is of 1 hp what is the height from which it can pull water ? And also if there is a bubbling sound of air and no water is being supplied what does it mean ?
- I will 'clarify' the question, then respond----- If you have a 1HP motor connected to a water pump,; what is its lifting capability ? (like raising the water UP from a well)... At or neat 'sea level', the very ideal (perfect) pump can lift water UP from 33 feet below. To be practical, considering in-efficiencies(losses) you should plan for about 25 feet of lift. Gurgling or bubbling of air/water is a good sign that the pump can not generate the vaccum-seal to begin the flow of water(priming process). You need to provide a way to prime the pump. To prime the pump, you need to supply a flow of water INTO the pump as it is running(water must be running backward into the well, then the pump will initiate the lifting process. To prevent the need to prime the pump everytime that you turn it on, you should put a check valve at the INTAKE orifice (the very end that sticks in the well). This will hold the column of water in the pipe; preventing it from running back into the well. (A check valve allows fluid to flow in one direction only....this must be connected such that the water can only flow UPWARD, out of the well. Good luck.....if you need further assistance, do email with more pump detail/specs. Make sure that the pump is rotating in the correct direction......
Send your message to us
miniature diaphragm pump
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
