Hot Dip Galvanized Iron Wires For Chainlink Fencing

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Commercial Galvanized Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

(7) Zinc Coating

Meet GB/T 15393 standard.

Q:2 long striaght wires (20m each) ,each having a 1.0A current going up.The distance between the two wires is 1.0m(a) what is the magnetic field (magnitude and direction) at a point o.50m left of the wire 1?(b)what is the magnetic field (magnitude and direction) at a point 0.6m right of Wire 1?: Assuming Wire 2 is to the right of Wire 1: a) Bwire1 = (u*I)/(2*pi*r) = ((4*pi*10^-7)*1A)/(2*pi*0.5) = 0.000004 Bwire2 = 0.000000424 Btotal = 0.000004424 (away from wire 1) b) Bwire1 = 0.000003333 Bwire2 = 0.000005 Btotal = -0.0000017 (toward Wire 1)

Q:I NEED TO CHECK IF A WIRE IS GOOD ON A FITNESS MACHINE. HOW DO I KNOW IF ITS GOOD? WHAT SHOULD THE OHMS BE?: Wire Ohms

Q:Got a new kenwood stereo to replace the old kenwood one in my VW polo 1998. Workes fine but when I pushed the stereo into my dashboard a wire came out so I pulled it out and put it back in. It worked, but next morning my car battery was near dead, I unplugged the stereo and its fine now. I assume I used wrong wire? Does anyone have a diagram or picture of how it should be wired?: When you wired it did you butcher the wires or use a wiring harness? With the wiring harness, everything is labeled and color coded. Match colors to the kenwood wiring harness, splice or use butt connectors, plug harness into factory harness and player, attach antenna wire and you're done! If you did butcher the wires and left enough wire, repair the harness and buy a harness kit at your local sound shop, really cheap too! Good luck!

Q:How do I tell which wire is positive and which wire is negative on the door speakers and the rear speakers?: Unplug the wires and note which wire goes where. then apply a battery to the speaker terminals, 9volt will work fine. If the cone moves out you have it connected to the proper + and - if it moves in then its backwards. With that you should be able to figure out which wires are + and -. Or you can just buy a service manual.

Q:What's the factors affecting resistance of a wire? and why? thank you!: Factors Affecting Resistance

Q:I've had my subs wired up for a while but want to see if there is a more efficient way to do it. Hardware: Sony Xplod 800w amp bridgeable amp - What's the best way to wire these up to get the most volume?: wire the voice coils to series on each sub and then wire the subs in parallel to the amp and voila.

Q:Does anyone have a schematic?: Did yer understand the international soccer cup. became as quickly as stolen out of a shop window, and a canine suggested as ''Pickles'' got here across it below a bush, what do yer think of roughly that then .. seem it up'

Q:Does anyone know what the wire harness is called that runs from the chassis to the door called on a 1995 jeep gc. This wire harness includes the speaker wires, power window wires, and power lock wires. I have checked everywhere and cannot see what this harness is called.: Its called a wire harness. I beleive it is the main dash wire harness, but you wont get anywhere with that if you are trying to get one from a parts house or dealer, You just have to hit and miss at the salvage yard or digging around yourself and get lucky. But if you can trace the wires to a block connector or firewall connector you will be in luck and just tell them the location of the block where the harness is connected and you should be there, just remember all your options in you truck will have to match the options in the donor truck or the harness wont work for you

Q:i need thin insulated wire like this.: it is called enameled magnet wire. try an electronics supply house or a motor and transformer electrical supply house. you can also purchase it online. you could also just take apart an old electric fan or door bell and unwind the magnetic wire. ~the other answerers don't understand wire, enameled magnet wire has a fine enamel insulation that needs to be sanded off in order to make a connection, as the enamel electrically insulates it to prevent an obvious short, but allows the inductive fields to easily pass through. it is used in all motors and most xfmr's.

Q:I need the wiring diagram for the factory radio of a 2008 ford explorer. i need to know which wires are for the back speakers so i can connect my Hi-Lo converter to it!? thanks: It would be easier to install an Line Output Converter on the rear speakers if the sub is going to be in the back. I personally would buy the harness pigtails for the speakers and the speaker harness. This would eliminate the need of cutting the factory wiring. You just pull the plug off the speakers in the back, and plug in the mate plug that will have a 2-wire pigtail that you would wire to LOC. The other plug with the pigtail would be plugged on the speakers.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range