Galvanized Steel Wire Rope Steel Wire Ropes With High Quality

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

steel wire rope
6*37+FC/IWS/IWR
6*7+FC/IWS
6*19+FC/IWS/IWR
6*24+7FC 6*15+7FC Be used for crane,hoist,engineering

galvanized steel wire rope

1. Application:

Crane, Hoist and General Engineering Purposes

2. Characteristic:

Good wear resistance and longer fatigue life

As per GB,JIS, RR-W,API and etc ,as well as customer`s request

3. Surface Coating: Galvanizing

4. Packing type: Wooden reel

Q: would the wiring harness on a 1.8 acura integra engine fit a 1.6 honda civic harness?: Yes.. As long as its an OBD0 to OBD0, OBD1 to OBD1, OBD2 to OBD2 and if it Vtec or non Vtec. If you try to swap an OBD1 to OBD2 don't work, and vise versa, If both are OBD2 and are both Vtec. yea it will work, you'll just have a couple of wire left if you use the harness from a 1.8 Vtec.

Q: Friend’s dog chewed my fuel pump wires on my 90 Chevy caprice classic I need to know what colors match up correctly. I have coming from the pump: Purple, Gray or (Tan color) black, only other wires in site coming from tail light harness are Pink, Gray, black/ white stripe. I have tested these wires and found out that the (black/white wire was ground, Pink was hot, Orange was hot not didn't light up as bright as the pink with the test light) Found nothing in Mitchell’s book to help also called dealers I printed out a wiring diagram but not much help..: 90 Caprice Classic

Q: but it says there are three Pink wires. There's not even three pink wires coming out of the car.The chassis/clip has been removed (by previous owner) and all that is left is the wires. All that is needed is a list of the colors and what they go to. Thanks.: Nissan Radio Wiring Diagram

Q: Will a subwoofer amplifier wiring kit be for the sub and the amplifier???? Because I'm searching online and I can find amplifier wiring kits, but not a subwoofer wiring kit. Only a subwoofer amplifier kit???: The amp kit should have everything for the amp. all you need for the subs is the speaker wire. make sure you get some good wire tho.

Q: So, I purchased a motion sensor light switch to replace the regular switches at my new condo. I have the wires exposed and I've identified the hot wire. My only problem is the hot wire (from inside the wall) is a single thick copper prong, whereas the wire for the motion sensor is split into like 15 different small copper wires.... I don't think the thick, single wire from the wall will work with the twisting wire connectors I purchased.... Am I able to just put the wires together and duct tape them??: You need wire nuts, conical plastic pieces with wire helical cones inside them... which sounds like what you have already. (It is not allowed to crimp solid wire - it weakens the wire.) Wire nuts come in different sizes; you will want the orange ones. To use the wire nut, lay the stranded wire alongside the solid wire, both stripped back about 3/8 inch, give the pair a gentle twist with your fingertips, and twist the wire nut on them until it stops or gets pretty hard to twist. Give a test pull on each wire.

Q: How much wire is required?: Length of wire is L = R*A/p SI units must be used, so convert radius to meters: r = 0.0254 / 64 m using 25.4mm = 1 inch r = 3.969*10^-4 m (0.3969mm) So cross-sectional area is A = pi*(3.969*10^-4)^2 m^2 A = 4.95*10^-7 m^2 The average resistivity of nichrome is p = 1.1*10^-6 ohm-meter So the required length of wire is L = 2.2 ohm * 4.95*10^-7 m^2 / 1.1*10^-6 ohm-meter L = 0.990 m

Q: And if anyone could give me percise instructions on wiring subs to 1 or 4 ohm that would be great. I have two dual 4 ohm subs and need to know how to solder wires or crimp wires.: JUST USE BLACK TAPE ,MAKES IT EASIER TO DEAL WITH LATER

Q: For my science project, need about 3 feet of copper wire...approx how much will that cost me? I want the wires to be pretty thin :): no. romex, household wiring, can be as little as $0.57/ft and i bett you don't really need 3 wire, 8 gauge romex for your project...

Q: What is a wiring harness?: If you buy an aftermarket cd player, you can get a harness for your specific type of car (walmart or auto parts store). That way you don't have to clip the wires and solder each one.

Q: Planning a study for my youth group. The name of the series will hopefully be 'Are you wired correctly?'. The basis would be having the right tools and so on to be on fire for God. Any ideas would be greatly appreciated!: Why Is Religion Extremely Daft. What Is Required Every Day Who is Really Exceedingly Delightful

Send your message to us

*Email

*TEL

*Quantity

*Unit