Aluminum T Plate

Hot Products

Suspended Ceiling System Ceiling T Grid T Bar

Suspension Ceiling Tee Grid-Acoustic Ceiling System

Suspension Ceiling Tee Grid-Galvanized Ceiling Grid

Galvanized Suspension Ceiling Tee Grid for Ceiling

Plain Ceiling T Grid Flat Ceiling System T15 T24 Ceiling Grid

Suspension Ceiling Tee Grid-Metal Ceiling Grid

Suspension Ceiling Tee Grid for Ceiling System

Suspension System Frame for Ceiling Tiles-Ceiling Tee Bar

Suspension Ceiling Tee Grid for Acoustic Ceiling

Drop ceiling grids metal ceiling grid from CNBM

FAQ

Can you put recessed lights in a drop ceiling ?

Can Lights For Drop Ceiling

we have had rain damage to our ceiling, how do i replace it

If they are the ceiling tiles that lay in a metal grid that's easy. Pick them up and drop new ones in. If they are the smaller ones that staple to the ceiling then just pull them and restaple new ones up. If thy come down hard you can take your utility knife and cut around the perimeter and then replace them . If they are not bad but just stained you can repaint then with a stain blocker paint. Good luck and have fun!

Construction Technology of Silicon and Caelite Ceiling in Light Steel

Construction process: ?? Bracelet → Striper Slot → Install keel → Install calcium silicate board

Is there any requirements regarding hard wired smoke detectors on a suspended ceiling?I know luminaires are supposed to be properly secured to the grid, do smoke and CO detectors need to be? If so how?Right now, all I have is some old work boxes for the splices.I'm looking for a correct answer, I'm not going to cut corners.NEC code references are a plus.

Not sure what they are called but they make a bar that goes from grid to grid with a clip on each end that you can mount a 4square box to in a drop ceiling call your local elec supply Store they will know

My fiancee and I are tearing down the drop ceiling in our family room. We've found someone to come take away the tiles, as they are in good condition, but we'd prefer to recycle the metal grid. Does anyone know what type of metal these grids are usually made of?

Aluminium perhaps ?

In carpentry and drywall when they refer to Black Iron on hanging ceilings what do they mean?

Black iron is the frame below the slab from which the hung ceiling grid or drywall studs are suspended and to which partition caps may be fastened. It defines maximum ceiling height for commercial tenant work. Piping, ductwork , and electrical work in the ceiling are also fastened to/routed through this supporting fame work.

My basement is being finished with a drop ceiling, and I am putting a small home theater in it. I bought an Optoma HD65 projector to mount on the drop ceiling...but how do I do it?! Can I use any universal projector ceiling mount or is there a special type I need to buy? What is the installation process?Thanks for your help.

how to mount electrical box to drop ceiling tile

Do not know who can tell me ah

Install the main keel 1) The main keel should hang on the boom. The main keel spacing 900 ~ 1000mm. The main keel is divided into light steel keel and T-shaped dragon bone. Light steel keel can be used UC50 keel and UC38 keel. The main keel should be parallel to the room to the long installation, at the same time should be From arch, arch height for the room span of 1/200 ~ 1/300. The cantilever section of the main keel should not be greater than 300mm, otherwise Should increase the boom. The main keel should be docked, and the butt joints of the adjacent keels should be staggered from each other. The main keel hangs well After the basic leveling. 2) Span greater than 15m above the ceiling, should be in the main keel, every 15m plus a large keel, and vertical main keel Welded firmly. 3) If there is a large modeling ceiling, the shape part of the application of angle or flat steel welded into a frame, and should be connected with the floor firmly. (6) install the keel Times keel clear keel and dark keel two. Dark keel ceiling: that is, when the installation panel cover the keel will be closed in the shed, in the The roof surface can not see the keel. Ming keel ceiling: the installation of the panel when the keel exposed under the cover panel, in the ceiling The surface can see the keel. The keel should be close to the main keel. Times keel spacing 300 ~ 600mm. Times the keel points T-shaped paint keel, T-shaped aluminum alloy keel, and a variety of strip buckle manufacturers with a dedicated keel. T-shaped galvanized When the sub-keel is fixed to the main keel, the ends of the keel shall be seated on the horizontal flange of the L-shaped keel On the bar buckle plate has a dedicated angle to do the keel. (7) cover panel installation Hanging roof cover panels commonly used plate with sound-absorbing mineral wool board, silicon calcium board, plastic plate, grille and a variety of Kouban, etc.