Self Priming Pump GMP-KMP
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Application: Industrial water supply and drainage.
Building site water supply and drainage.
Irrigation and drainage for agricultural and horticultural.
Drainage for sewer and purifying tanks.
Drainage for waste water treatment.
--------------------------------------------------------------------------------
Feature: 1. Direct Struction of a common axis. high efficiency. compact design, light weight, save space and easy to install.
2. With mechanical seal that guarantees leakage-free. shaft never damaged, save the trouble of intercalating gland packing and lengthen the life expectancy.
3. Special construction for the pump casing, high self priming capability.
4. With half open-type impeller which drainages waste water effectively.
5. Special minor impeller design helps to minimize the pressure imposed on the axis and motion lost. More effective than the balanced-hole design. Only initial water-adding is required to save the trouble of continously water-addings.
- Q: We bought a plot of land and me and my father found a deactivated water well in there. We checked and it's 328 feet deep and is still full of water.How would i go about setting up a pump on it?
- Water pump setup? We bought a plot of land and me and my father found a deactivated water well in there. We checked and it's 328 feet deep and is still full of water. How would i go about setting up a pump on it? Best thing to do is call a plumber and ask about hooking up a well to a house. You can use a submersible pump or have the pump located somewhere near the well head or in a building nearby (a pump house say). Because it is so involved and back-breaking work, it is better to hire a PRO.
- Q: All water pump have diferent caracteristics, but it is imposible to overcome a certain hight...what is that hight and why?
- The height limit stems from the fact that water exerts a tremendous amount of pressure. If you have enough water, then the pressure will be so large, that no practical amount of force will be large enough to pump water. Not sure what the height is, but I'm sure you can google it. I.E. Maximum absorption height of a water pump
- Q: how much is it to replace timing belt and water pump on a Chrysler voyager 2002?????
- Timing belt can be be anywhere from $200 to $400,but make sure a pro does it beaches if it's put on wrong and off time it can mess up your engine and that would be in the thous..this happened to me.. Water pump idk
- Q: i have a jetta and would like to know how difficult it would be to do. I know its a german car this is why i ask. thanks
- Looks like you're covered with the mechanical aspect of your question! My input involves your comment on its a german car. I have several friends that are mechanics/techs. To a man, they say it doesnt matter what make (Japanese, American,European,Korean,etc.) the manufacturer assembles each for its ease of assembly at the factory. Ease of repair is a secondary consideration. All you have to do is look at their skinned knuckles as proof ! They all well deserve their paychecks!
- Q: Why should the pump fill the air before running? What's the reason why the water doesn't go up?
- By rotating the water pump is thrown from the impeller center, resulting in pressure, the back of the water sucking over, this is the pump working principle, if air, air will not be left out without impeller, the flow rule, no pressure, so we can not draw water!
- Q: water pump on a Suzuki forenzakia optima
- The suzuki ( I done it for a 05 due to you had no year); OEM Part cost Water Pump 1740085Z00 $203.67 Water Pump Replace 2.0 hours Timing Belt 1276185Z01 $92.05 Timing Belt Replace 1.8 The cost of doing the water pump and timing belt; Parts: 295.72 Labor : 3 hours times the shop labor rate. The kia has what engine in it???
- Q: water pump pulley has slight wobble in it. not seeing water yet....is bearing going bad
- Water Pump Pulley Wobble
- Q: Earlier today I was driving and my car shut off at a stop sign. I got it to start again and it shut off at the next stop sign, so after a few minutes I got it to start again and immediately pulled over as there was a small amount of smoke coming from under my hood. The temp gauge didn't say it was overheating, but I think it mightve been stuck, because that had to be what happened. After sitting there for a while it started and stayed that way for a while, I let the engine run. I drove it to the gas station and put some coolant directly in the radiator and the resevoir, and almost all of it leaked right out. I started to drive it home and had to pull over about 6 times to let it cool down because it kept overheating( temp gauge showed it this time). I think its the water pump that is leaking, but I know very little about cars, and was wondering if it could be anything else? Also, the heater wasn't working in the car today at all.
- This Site Might Help You. RE: water pump leaking? 99 dodge neon? Earlier today I was driving and my car shut off at a stop sign. I got it to start again and it shut off at the next stop sign, so after a few minutes I got it to start again and immediately pulled over as there was a small amount of smoke coming from under my hood. The temp gauge didn't say it...
- Q: I have a 2000 chevy impala with 85K on it. I have heard/a weird rattle noise from under the hood for some time now. I once asked about it on here and got suggestions regarding front end problems. I had that checked out and the front end is good. I still have the rattle noise along with a high pitched, but not very loud, squeeling noise when I accelerate. I am leaking coolant and it seems to be coming from near one of the belts. Is this a bad water pump? If so how expensive of a fix is it and how involved of a repair is it?
- It sounds like a water pump or maybe a loose connection. It is probably time for a water pump if it hasn't been replaced yet. Parts will run under $60 and it probably involves an hour of labor. The Impala is a big car, it shouldn't be hard to get to and remove. Taking it to a shop will run under $100-$150 for everything.
- Q: What is the difference between a low pressure pump and a high pressure pump?
- The magnitude of the pressure at the outlet side of the pump
Send your message to us
Self Priming Pump GMP-KMP
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords