SELF Priming Water pump MQS126A Clean Water pump

SELF Priming Water pump MQS126A Clean Water pump

Ref Price:

Loading Port:: Shanghai

Payment Terms:: TT OR LC

Min Order Qty:: 10 set

Supply Capability:: 100 set/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Packaging & Delivery

Packaging Detail:	1 in 1 or 2 in 1 Brown Box
Delivery Detail:	30 Days Afrer Received Deposit

Specifications

1. Clean water pump 2. Copper wire, Brass impeller 3. Brass Front Flange 4.Good quality 5.Low Noise. 6.Power: 0.5 HP

Product Description

MQS126 Series Electric Single Phase Priming Clean Water Pump

◊ Application

Applied to pumping such liquid which is clean, no solid matter or frictional matter, low viscous, noncorrosive, non-crystallizable, chemically neutral and close to water. Such as:

1. Tank filling

2. Domestic water supply

3. Water transfer

4. Pressure boosting

5. Irrigation

◊ Features

100%copper wire
Brass impeller
Cold-rolled silicon steel sheet, with high-speed punching, improve the efficiency and precision.
CNC precision automatic lathe for smoother shaft
Strict test including high-pot testing of stator coil and whole pump, outgasing test and performance test, ect
Anti-rust treatment castings and electrophoresis.

Packaging & Shipping

MQS126A : 2 PCS in 1 brown carton. Inner box can be color boc(depands on quantity) design can be as customers requirement.

Shipping Date: 30 Days After Taizhou Qiangwei Pump Co., LTD. received the Deposit.

1×20FT Container can load : 2100pcs of MQS126A

Q: 7.63Determine the isentropic efficency of a water pump when water enters as a saturated liquid at 96.5 kPa and exits at 5 MPa and 106 degrees C.Thanks: Well!!!!!!!! Isentroipc Efficiency of a pump = Isentropic Work / Actual Work At state 1, Enthalpy of Saturated Liquid h1 = 413.357 kJ/kg Entopy s1 = 1.29154 kJ/kg-K At state 2, Enthalpy of Liquid at state 2 = 448.042 kJ/kg Now, to find the ideal Enthaply , Enthalpy at 5 M Pa at entropy of 1.29154 kJ/kg-K h2s = 418.462 kJ/kg Thus, Isentropic Work Done I = h2s - h1 = 418.462 - 413.357 = 5.105 kJ/kg Actual Work Done A = h2- h1 = 448.042 - 413.357 = 34.685 kJ/kg Hence, Isentropic Efficiency = I/A = 5.105/34.685 = 14.72%

Q: The leak is in the same area as my water pump, but when I jacked my car up yesterday, I wasn't able see my water pump. It's a 99 Saturn SL1.With the leak, it leaks very slowly, and it only leaks about a few ounces of fluid at a time. It mostly only leaks when I start the engine while its cooled down, and it's leaking down the passenger side of my engine.If it was a bad water pump, would the antifreeze leak without stopping until all of the antifreeze is gone?: When the water pump seal fails it's either because the water pump bushing/bearing is bad or because someone was running straight water in the cooling system. Once a water pump starts to leak it needs to be replaced immediately. If you let it go it will start to leak more and faster as the seal deteriorates. You will spend more money topping up the system with antifreeze then to just fix it. The other thing that will happen is you will get caught as it fails completely and overheat the motor causing thousands in damages or at least need a tow which once again will cost more than replacing the water pump.

Q: Where is the water pump located on a 1993 mitsubishi eclipse with a 1.8 motor: it is belt driven pulley near the center of engine, unless mitsu made that one timing belt driven in which case you can't see it with-out dissassembling front part of engine.

Q: I have been given a project to build a windmill driven water pump. So far, a lot of the books I've researched only give me info on how a water pump works. Can anyone help me with this? Thanks in advance: How Do Windmills Pump Water

Q: need step by step on how to change water pump: Remember that the water pump is reversed as for removing installing. You tighten to remove it loosen it to install it. Also, it only goes in there 1 way!!!! Do not force it or you will be replacing the crossover which aint cheap. Before removing the old one, look at the new water pump founf the notch or different sized tab, it goes in a certain spot. Look at the old one, make sure to take note of where that tab is sitting in the crossover.

Q: 22KW pump motor direct start circuit breaker and contactor size? Concrete calculation method: Strictly speaking, eleven kilowatts or more is not allowed to start directly

Q: I am about to replace the timing belt in a 3.4L Toyota V6 at approximately 85,000 miles. The motor has had the Toyota red coolant, which lubricates a water pump very well. Should I, Or should I not replace a Toyota Water Pump also, at this mileage (85,000)? Could the original water pump last until 170,000? Thank you: It's recommended to change the water pump also because your labor cost to open the engine to change the belt, is the exact cost of any future labor cost to change the water pump which, will go bad, eventually. The original pump could last until 170,000 miles but why chance it when the engine is already opened up.

Q: i was wondering how hard it would be to chancge a water pump in a 1997 chrysler sebring.: I had a 97 Eagle Vision that had a lot of the same internals as the Sebring, Intrepid, etc... I went through 4 water pumps on it and eventually got rid of it because of the lemon laws. From what I remember back then it is an electric water pump with an absolutely horrid location for mounting. I am going to guess that it's something best left to an ASE type of of mechanic.

Q: Do you need a stop valve for the pump at home?: It is better to connect with the pump. If it is a self suction pump, it can not be connected, but when it is pumped, it does not immediately have water, and the submersible pump is not necessaryMy home is a self suction pump, fully automatic control, I took the check valve, in the pump suction port position is very good, as long as it has started, there will be water out

Q: My car is overheating and i don't know why just trying to rule out as many options as possible.Things it is most likely not: blown gasket/cracked head, both replaced 2 years ago and no tell tale signs I will be doing a block test soon, thermostat replaced it and put the old one in hot water and it opened, hoses replaced with new one two years ago, no leaks pressure test a few days ago. Things yet to be ruled out The radiator being clogged or not allowing good airflow, water pump impeller failure.: if you have no fan activity, it will get hot at low speeds and at a stop position.

Send your message to us

*Email

*TEL

*Quantity

*Unit