Metalshield flame-retardant and flame resistant power cable
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 10000 m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Application
This product is suitable for rated voltage 0.6 / 1kV and below of transporting electricity. This product has a strong anti-electromagnetic interference, anti-lightning and a uniform electric field, improve power quality characteristics. Especially for sophisticated electronic device places, such as computer center, aerospace monitoring center, intelligent building.
2. Type and Specification
Voltage | 0.6/1 kV |
Type | ZN-VV-P2、ZN-YJV-P2、ZN-VLV-P2、ZN-YJLV-P2、ZN-VV22-P2、ZN-VV32-P2、ZN-VV42-P2、ZN-YJV22-P2、ZN-YJV32-P2、ZN-YJV42-P2、ZN-VLV22-P2、ZN-VLV32-P2、ZN-VLV42-P2、ZN-YJLV22-P2、ZN-YJLV32-P2、ZN-YJLV42-P2 |
Size(mm2) | 1 Core:4~300; 2 Core:4~185; 3、 4、 3+1 Core:4~300 |
Standard | GB/T 12706-2008 |
3. Using features
① Rated voltage Uo/U 0.6/1 kV.
② The permissible maximum conductor operating temperature: XLPE insulated 90 ℃, PVC insulated 70 ℃.
③ Cable short circuit (the longest duration of no more than 5s), the maximum temperature of the conductor: XLPE insulated cable 250 ℃, PVC insulated cable 160 ℃.
④ Laying the ambient temperature should not be less than 0 ℃, should be less than 0 ℃ pre-heated. Cable bending radius: Single cable without armor no less than 20 times the cable diameter, armored not less than 15 times the cable diameter; multi-core cables without armor is not less than 15 times the cable diameter, armored not less than 12 times the cable diameter.
⑤ Finished cable should be subject to 2.5U0 + 2kV power frequency voltage test 5 min without breakdown.
⑥ DC resistance of conductor at 20 ℃ comply with GB / T 3956.
⑦ Finished cable with anti-electromagnetic interference, anti-lightning and other characteristics.
⑧ Cable fire-resistant characteristics comply with the requirements GB / T 19666.
4. Picture of structure
1、Conductor 2、Insulation 3、Filler 4、Tape 5、Inner Sheath 6、Metalshield 7、Outer Sheath
- Q: Since the ps3 uses a universal power cable can any of those cables workthe original cable says 10A and 125v and the other non original says the same it fits however is it safe???
- If you are talking about the HDMI cable that goes from your HD TV to the ps3 - then you have to find out the resolution that your tv supports and then find a HDMI cable that matches that resolution you can get these cables at major electronics stores It is best to have a HD TV with the HD cable (improves graphics)
- Q: Hey! I bought a new sound system for my truck including 4 new speakers, a sub, a 5-channel amp, and I'm running all new wiring. So far I've got the 3 RCA cables ran, along with the blue remote turn-on wire along the right side of my truck. I plan to run the Power wire down the left side and then to my amp.I've heard that you put the power wire and RCA cables on different sides, which is what I've done, but is it ok for my speaker wires to be run beside or close to the power wire(4-gauge fyi)?For example, the right side speaker wires wont be near it, but the left side speaker wires will be...Will this cause any weird noise from my speakers?I don't have the names/etc of all my gear right in front of me, but if u rly need it, I will quot;add detailsfor you! Thanks!!
- Separating the power the speaker wires is not as important in a car that uses DC voltage as it is in a home system that has AC voltage. It certainly doesn't hurt anything, tho.... If you do run them across each other, keep the intersection as close to a good right angle as possible. And, air is a very good insulator, so keeping some distance between the power the speaker wires is also very good.
- Q: Cable WDZ-YJFE2 (4X185 + 1X95) what does it mean Cable WDZ-YJFE2 (4X185 + 1X95) What does it mean? More
- According to the specification requirements: 8.10 cable bridge wiring 8.10.4 cable bridge horizontal laying, should be selected according to the load curve to support the best span, span should be 1.5-3m. Vertical laying, the fixed point spacing should not be 2m. Assuming that the height of the electrical shaft is 60 m and the fixed point spacing is 2 m, then the number of stents required is: (60/2) * 2 = 60 Assuming that the height of the electrical shaft is 60 m and the fixed point spacing is 1.5 m The number is: (60 / 1.5) * 2 = 80 mainly depends on your shaft height, and the bridge fixed point spacing, hope to help you, (* ^ __ ^ *)
- Q: I am trying to run the power cable leading to the amplifier in my car but can not seem to find a hole or firewall to pass the wire through. My car is a 91 Toyota Tercel. Please and Thank you
- The Tercel will have a couple of un-used holes that are covered with black solid rubber grommets. You can poke a hole through one with a pen or screw driver and just push the wire through. You should find these holes one the left and right symmetrically, and they will be near half way down, but closer to the top than bottom. If you can't see them, maybe you can feel for them.
- Q: i wanna know how much distance should be in between the power cable and the cat5 cable
- after standards cat5 cables are not run parralell with power cables, instead intersected
- Q: which cables cant be near each other??(will cause noise radiation if put together)i gotta run some wires through my car and i dont know wich ones to keep away from others. im runnin...4 gauge (eventually will be 2 gauge) power wire for amp2 speaker wires for rear deck speakersrca cables for ampremote turn on wire for amp
- It does not seem likely that you will have a substantial problem with noise from speaker cables going through power cables and then the amp. Besides sheilding, use of capacitors on the power cable at the amp end (follow correct polarity on electrolytic types) will kill noise. A properly-rated, and connected, Zener diode is another step. Such things as antenna-leads are so sensitive that they are always well-shielded. ______________________________________... As for zener diode use, I have never heard of them being used in this application. But then, many new ideas have never been applied before. Sparky has pestered me with not one, but *two* hostile emails and is in some state of jealous frustration. He can't seem to figure how one could supress overvoltage transients using a zener (duh). If he had asked respectfully, I would have told him what I was thinking, but since he is determined to be a jerk about it, then whatever...
- Q: Does throwing punches with weighted cables increase punching power?
- No power is genetics. You either have it or dont. It'll increase speed. Don't do to heavy or you'll damage your ligaments and tendons long term.
- Q: I am buying a graphics card with a 6-pin power cable connection, but i have no six pin power connections, so i need a converter that converts two molex (four pin) plugs into the 6-pin plug that i need. But i have no molex pins, so i need to convert my two sata 15-pin cables to molex pins so that i can complete the circuit. will this work without risking damage to anything, and will it work in the first place?Also, do i HAVE to use _two_ molex cables to make the pci-e (six pin) cable?
- hi confident you are able to, you need to purchase FDD 4 pin Molex to finished length Molex adapters or only butcher the cable and solder the recent MOLEX on and use some electric tape on the bare wires (would not seem exceptionally).
- Q: power supply, however it comes with some cables that can be attached to the peripheral 4 point cable then ran into the card itself. can this setup work? Or will I need a new power supply with 2 6 point pci express power cables? Oh by the way its a 600 watt power supply I currently have.
- The addapter to the 4pin molex will work just fine. If your pickie about your computer like I am, then you can purchase a new power supply, but there really isnt any need.
- Q: I'm new to PCs and I recently bought a Dell Optiplex 745 desktop PC but it came without cables. I thought I had the correct power cord but it turns out I gave it away to friends. I have the power cable that you plug into the wall which has the standard PC kettle plug (the correct one for PCs not an actual kettle plug) that you'd usually plug into an adapter then into your PC but I'm not sure if you can just plug it in without the correct adapter. I have Googled but cant make head nor tail of it all. And by adapter I mean the cable with the little box that you usually plug into a device such as a PC, laptop or Xbox 360 before you connect the cable to the mains.Thanks.
- It all comes down to the amount of output that the pc is set to take. I would think that you would be fine without the adapter, assuming it already works. If you do decide to do this make sure you set up a surge protector, dont just plug it into the wall. A power surge could fry the internals and brick the pc.
Send your message to us
Metalshield flame-retardant and flame resistant power cable
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 10000 m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords