Galvanized binding wire、Iron tie wire
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 20 m.t.
- Supply Capability:
- 700 m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Production process: it uses the high quality low carbon steel wire rodprocessing, is made of high quality low carbon steel, the drawing,pickling, annealing, galvanizing. The cooling process and processing.
Characteristics: galvanized steel wire has good toughness and elasticity,the highest volume of zinc can be up to 300 grams / square meter. Has galvanized layer thickness, strong corrosion resistance and other properties.
Application: galvanized wire products are widely used in architecture,handicrafts, silk screen preparation, highway barriers, product packaging and daily civil, and other fields.
Galvanized wire and divided into hot dip galvanized wire and cold galvanized wire (galvanized wire) to distinguish:
Hot dip galvanizing is dipping in zinc liquid heating melting, fast production, coating thickness but not even, the minimum thickness of the market allows the 45 microns, the maximum of 300 microns above. Color is dark, zinc metal consumption, infiltration layer is formed with the base metal, good corrosion resistance, hot dip galvanized outdoor environmentcan keep decades.
Cold galvanizing zinc (Galvanized) is gradually plating metal appearancethrough the current direction in the plating tank, production speed is slow,uniform coating, thin, usually only 3-15 micron, bright appearance,corrosion resistance is poor, generally a few months will rust.
The hot dip galvanized, electric galvanized low production cost.
Cold galvanized and hot dip galvanized difference:
Cold galvanized and hot dip galvanizing is the difference between the amount of zinc, can identify them from the color, cold galvanized colorhair silvery white with yellow. Hot dip galvanized hair white.
- Q: I found an old Karavan flatbed utility trailer and am currently converting it into a snowmobile trailer (2 place). Me and a friend riped all the wire off of the trailer and completely rewired it. No matter how we configure it, the lights aren't coordinated. If we hit the left blinker in the car, all the lights flash(like the hazards are on). Right blinker works fine. we wired it first from the diagram on the karavan site. Now once we think about it, they have us wiring the ground into the light. so we searched the web and found this layout.
- You need to buy one specific to your tow vehicle if you have a 5-wire system and one sure way to determine if you have a 5-wire system is if your rear turn signals have an amber lens. But not all 5-wire systems have amber lens on the rear turn signals so don't let that be the only determining factor. Check for yourself, or better yet, call a U-Haul center an tell them the year, make, and model of your tow vehicle and ask them if you need a converter harness. They will tell you what you need. But I am almost positive that the Chrysler Town and Country will need a converter harness.
- Q: Can old speaker wire cause a little static sound??
- The only way I could see old wire causing what you describe is if there is a lot of oxidation on the part where it is making contact. It is possible, but not likely and just simply jiggling things should cause the oxidation to come off, if that is what it is.
- Q: Someone Stole my stock radio out of my car (They cut it out) Now All i have in the is wires and I cannot afford to go get a new one installed.Here are the wires that are in my car
- what you need to do is buy the book for your car at autozone. and look at the radio wiring diagram. i had a similiar porblem but with the book it shall tell you were to hook the wires
- Q: I have a universal 02 sensor 4 wire (black, black, white and blue) the stock is white black and grey how do I wire it? thanks :)
- Keep in mind the sensor has a signal wire, a ground wire and a heater wire (or wires). Good luck!
- Q: My dog chewed the wiring and i dont know how to re-connect
- just reconnect like-colored wires back together
- Q: I'm wiring up a kenwood sub and amp. Everything is connected except for a quot;power control wirequot;. Not sure what this does or where I should connect it to. Any help?
- Control Wire
- Q: The t-stat comes with EIT module. that wires to the t-stat and the furnace. I'm having trouble with the module to furnace wiring.
- from the thermostat you match 1,2,3 wires to the module, from the module to the furnace. - R to R (this is your 24V hot) W to W (furnace 24V input G to G (fan for cooling 24V input) Y to Y (cooling 24V input), there should also be another wire that connects with this that goes to the condensing unit C to C ( Common - must have this connected for IAQ to work) as with the Y, there should be another wire to connect to this that goes to the condensing unit. - maybe W2 to W2 if you have a 2 stage furnace, you'll know if you have a 2 stage furnace because the W2 connection on the furnace will be present. - maybe Y2, if you have 2-stage cooling. if you have a humidifier connect both wires from the humidifier selinoid valve to each of the HUM terminals.
- Q: Is there special speaker wire in order to run 250 watts max rms or will the oem speaker wire in the car be sufficient (did not originally have an amp and is most likely at 50 watts max rms). If I need a special wire for that please let me know what it is called and possibly an example link. Thanks!
- most likely the wire pre ran in the car was 16 guage wire which is fairly small id recomend atleast 12G for speakers and 8G for a power wire.
- Q: I have 4 gauge wiring ground and power cables, as well as a smaller guage wiring that is colored grey. I have the amp hooked up to the gound and power, how do I connect the sub to the amp?The subs is a 08 L7 in the kicker truck box wired to 2 ohms. The amp is the Alpine PDX 1.600.
- take (i use 12 gauge wire on my sub installs) 16-14 gauge wire and hook up the positive on the amp to the red terminal on the sub and negative to the black one. I'm not really sure what you need exactly
- Q: what wires do i use to bridge subs together?
- 12 awg twine is superb....yet i do no longer understand your question. Are you attempting to parallel or sequence the voice coils? Paralle. tie the two together. constructive to constructive. detrimental to detrimental. which would be a 2 ohm load. sequence. in basic terms run the bounce twine from constructive of one coil to detrimental of the 2nd coil. which would be a 8 ohm load. Assuming the coils are 4 ohm..wish that enables.
Send your message to us
Galvanized binding wire、Iron tie wire
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 20 m.t.
- Supply Capability:
- 700 m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
