For 4-Pin Ide 1 To 3 Splitter Power Cable
- Loading Port:
- China Main Port
- Payment Terms:
- T/T
- Min Order Qty:
- 10 Pieces pc
- Supply Capability:
- 500 Piece/Pieces per Day pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Simply plug the splitter to a power connector and triple it to three connectors to power more than one adding HDD or CD/DVD ROM or any 4 pin power source you may have, no need to worry about future drive addition.
Used to connect 4 pin power fans to cool your PC while using it, enhance the hard disk performance in a cooling environment
Make the most of the supplied power, efficiently handing it over to your adding drives at the maximum safe rate
- 4 pin IDE 1 to 3 splitter power cable.
- Connectors: 4 pin IDE 1 male to 3 female.
- Cable Length: 20 cm
Why we choose Okorder.com?
Okorder.com is a professional and reliable online E-market place
Providing a variety of products with reasonable prices
High quality goods provided by factory suppliers
Shipping to over 200 countries.
One-stop sourcing
Dubai Logistic Complex
Okorder Quality Control?
We hold a very strict quality control system to check every connector of our products for your safety.
Okorder services for you
1.7*24 hours Hotline & Email Service
2. Your inquiry related to our products or prices will be replied in 24hrs.
3. Well-trained and experienced staffs to answer all your enquires in fluent English
4. OEM&ODM, any your customized demand we can help you to design and put into product.
5. Distributor ship are offered for your unique design and some our current models
- Q: Or better yet is there a 100' snake with phantom power? Can't seem to find anything online.
- Absolutely! Currently, we power all of our condenser mics with phantom power through lines that are over 300' long. The power required is miniscule, therefore the current flow to power them is also very small. The voltage drop is what will eventually cause the mic to stop working, but that will require thousands of feet of cable, especially at 48 volts, if that is the rating of your phantom power supply (can be 11 to 48 volts).
- Q: Did not find the relevant norms. Fiber optic cable should not be affected by interference, electric corrosion this piece without taking into account? More
- Cable can be parallel with the 10kV power cable laying, there is no distance requirements, two cables walking in a metal bridge is no problem. Fiber optic cable is through the optical communication, the power line of electromagnetic waves will not have an impact on it, there is no problem of electrical corrosion, because the cable is protected by an outer sheath. Now in the high-voltage cable directly attached to the internal fiber and power supply and communication, but also in the high-voltage overhead lines directly on the composite fiber (OPGW), while the power supply and power grid communication. Fiber optic cable, is a certain number of fiber in accordance with a certain way to form a cable core, outsourcing jacket, and some also cover the outer cover, used to achieve optical signal transmission of a communication line. Generally consists of cable core, reinforced steel wire, filler and jacket and other parts of the composition, as well as the need for waterproof layer, buffer layer, insulated metal wire and other components.
- Q: Power cable 5-color line, respectively, what color, what role?
- YJ: cross-linked polyethylene insulation V: PVC sheathed 22: steel tape armor 8.7 / 15KV: rated voltage: 8.7 / 15 kV 3 * 300: three conductor cross-section of 300 square copper conductor Another: such as YJLV Is the aluminum core. Here is not marked what the material is conductor, you can default to copper conductor.
- Q: Why cross bonding in power cable?
- If so, the answer is: By tying multiple cables together, the current carrying capacity of the total cable is increased without having the total cost increase in proportion. In other words -- using the picture as an example -- tying 4 equal sized cables together increases the current carrying capacity by a factor of 4, but the cost of this multiple-wire cable is less than the cost of a larger single cable that would carry an equal amount of current. .
- Q: My old card only needed one of these cables. but my new 4870 will need two. can i just use a IDE-to-PCI-e power cable? its only got 3 wires out of the 6 though. does this matter?
- You okorder /... It takes two 4-pin PSU molex connectors and converts it into 1 6-pin PCIe connector. Make sure your PSU can supply the necessary amps on its +12V rails, and if you got a PSU with multiple +12V rails, you need to make sure you got the load spread out among different rails to avoid overloading one rail.
- Q: Single single 10kV power cable with copper shield can wear steel pipe? What will be the impact?
- Do not have to be so troublesome, such a phenomenon even encountered, is the basement of the air defense, similar to the landlord said the phenomenon can be taken as follows: . first with linen live wire and casing blank. . filled with asbestos cement and compaction, the surface concave sleeve 3-4 cm. . with plugging the king (5 yuan / bag) add water and mix well, smear the surface to smooth. . the work is completed, do not hurt the core and the practice proved no leakage within two years.
- Q: My setup is an alpine MRX-M100 powering 2 alpine type R 12's on 4 ohm, and also an old eclipse PA 5422 speaker amp. The main thing is I have 4 gauge running from my battery to my amps, but I have this sort of distribution block that turns the 4 gauge wire into 2 8 gauge wires. I know that this probably isn't the best for the MRX-M100, but it's all I had or what I could afford at the time. The main thing I wanted to ask was is this bad for the amp, and what would it be like if I had 0 gauge coming off the battery so then it would be 4 gauge going to the amps? Would it be louder? Could I turn it up higher? because right now if I turn up the volume past a certain point the subs will just stop playing. If I just shut off my head unit and turn it back on they start up again. Your thoughts and recommendations would be appreciated!
- then (big three upgrade)watch a video on this.its some wiring upgrades under the hood.if your sub woofer is cutting out like you said its not getting enough power.any charging system upgrades you can do will help.remember this the alternator is the heart of your charging system if you have a chance to swap this out at least buy one that puts out at least double the amps that your factory alternator is putting out.this will not harm your car and will do wonders for your sound system.
- Q: One of my ottocinclus is munching on a little brown algae that's on the aquarium heater's power cable. Not dangerous, I guess? I don't think they can actually bite through it and expose the wire...?
- No it isn't dangerous at all. He will be fine. I love otos. They are so darn cute.
- Q: So I'm currently living in a dorm room, and my tv is hooked up to the campus cable system. A couple of minutes ago, the power went off and turned back on right away, and I was watching tv during this. Now the power is working but the cable is not, all the channels are nothing but static.I've tried resetting my tv, but I'm wondering what else I could do. Other tvs hooked up to cable in my dorm aren't working either, so is there something wrong with the entire cable system?
- Yes, there has to be a problem in the cable system.
- Q: What is the concept of power cable middle head? What is the difference between a terminal and a terminal?
- Cabling in the integrated wiring system according to the network topology diagram to configure how to connect, no network topology is unable to give the correct connection.
Send your message to us
For 4-Pin Ide 1 To 3 Splitter Power Cable
- Loading Port:
- China Main Port
- Payment Terms:
- T/T
- Min Order Qty:
- 10 Pieces pc
- Supply Capability:
- 500 Piece/Pieces per Day pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords