F-KB003 rubber wood knife box,your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
product name：rubber wood knife seat
material：rubber wood
N.W.：1.642kg
MEAS：34.5*22*4cm
Specifications:
Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense
Excellent toughness, process into various curved according to the needs , full of beauty
Solid texture，manufactured goods with firm structure，prolonged service life
The texture of rubber wood is fine and closely woven，pore full of lots ot padding so it's hard to absorb water and corrode.
Description：
1、The knife seat use material of high quality natural rubber wood and take professional advanced machine equipment and manual binding.
2、The knife seat was refined by material, assembly, polishing, painting and other procedures.
3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.
4、Hoteam commerce co.，LTD，is a manufactory specialized in all kinds of wood knife handles，wood seats，chopping boards and other woodworks.
5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure that dry and clean and put it in the open air
- Q: After the work of the machine tool, the knife is not changed, the time is good and bad, the circuit is not a problem, mechanical rotation is normal. What are the specific reasons
- Check your phone when the good or bad adjustment should be able to keep the turret is not in place after the rotation of the signal to detect the location of the sensor block or the location of the adjustment of your Holzer like
- Q: What are the reasons for the deviation of the CNC lathe tool holder after each turn
- Do you mean that the deviation is not parallel to the axis of the spindle after the lock is locked, or if you have the same knife position
- Q: CNC lathe turret in place how to do
- Tool change:1, the machine tool holder after the knife, the knife is a mechanical problem, the center of high deviation2 turret Rihall element, proximity switch, encoder, damage. Or poor contact, or 24 volt supply knife is not normal.3 according to the different types of tool holder, check the tool manual, with the electrical schematic diagram and ladder diagram to find out the cause of the fault.
- Q: CNC lathe tool holder four and six stations which good
- The internal structure of the turret principle is similar, but the four station looks like car carriage, six station is a brick tower structure, slightly larger, a fixture of processing content more, six station processing large size parts, the adjacent knife knife may interfere with the four station, six station four station your. Think about it.
- Q: How to do the slide shoe
- Nails can be used as follows.Use a hammer to hammer the bigger one in the mouth, then screw it.In addition, there is a special tool for dealing with sliding wire. You can break a nail.Knife slide wire no way, can only change the tool holder. Even if the wire tapping to do the thread, the diameter is not the same as the original
- Q: Tool holder S solution
- Vertical typeThe wheel frame, in fact, is a parallel steel frame structure.Than S, there are many advantages.For example, solid, DIY, modification, etc.
- Q: For what parts of the process, what is the difference between the installation
- With the knife is like a long knife, to prevent the use of knives to make the knife, the center frame is used for the processing of slender shaft, to prevent the processing of slender shaft shape into the middle of the coarse two fine
- Q: What are the advantages and disadvantages of CNC lathe turret
- CNC lathe in the use of the process, the common fault of the tool holder, spindle, thread processing class, the system display class, drive class, communications and other failures, and the tool holder fault occupies a large proportion. After the failure of the machine can not be used temporarily, resulting in a waste of manpower and material resources in time. If we can do some basic maintenance, we can save costs, save time and create a certain economic benefits.
- Q: How do you know how to install the roller skates?
- If you are able to disassemble the wheel of the kind of one-piece knife, the general is divided into 165 holes and the distance between the 195 holes, the general number of roller skates is the distance between the 165 holes of the.When installing tool holder is according to personal habits, but most were filled with the knife knife mounted on the middle sole. That is, the wheel is about the same length as the shoe. This is more comfortable. Of course, there are special requirements in order to toe and heel action to do better, but also will be installed on the front or back.
- Q: The difference between the turret and the rear turret NC lathe
- No big difference, mainly to see the design of machine tool manufacturers have their own customized. Such as the electric knife in front of their own called the front tool holder, with the opposite of the rear cutter. There is also a row of knives, in the car arc, the knife installed on the back of the knife, the programming instructions to be divided into circular arc, arc
Send your message to us
F-KB003 rubber wood knife box,your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
