Non-Stick Colorful Knife Set
- Ref Price:
-
- Loading Port:
- ShenZhen
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 sets set
- Supply Capability:
- 1000000 Set set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Advantage Of Non-Stick Colorful Knife Set:
1.Good Quality :Made of 100% food grade Material.
2.Competitive price: We always support our customers’ business with competitive price.
3.Good Service : We treat clients as friend.
4.Low MOQ: It can meet your promotional business very well.
5.OEM Accepted : We would be glad to help develop your new design product item.
Usage of Non-Stick Colorful Knife Set:
Family used, hotel, restaurant, wedding party, supermarket, retail shop, promotion, gift etc.
Our factory supply all kinds of stainless steel tableware, west tableware, cutlery set, gifts tableware,Kitchen utensils,Kitchen knives,pot.style variety, exquisite workmanship, beautiful and practical, suitable for restaurants or home use, made of high quality stainless steel and high quality, of the production process can be high temperature sterilization, used for a long time, plans to welcome new and old customers to sample processing customized, we will with the fastest speed to reward all the customers the best quality!
Remark of Non-Stick Colorful Knife Set:
Every terms mentioned above are flexible.
The products in our company can respond to your requirement, no matter the size, length, thickness, the material, even the packing details. We hold on the principle of "meet every requirement of our customers".
I am sure you can find the one you like.
Company Profile of Non-Stick Colorful Knife Set:
We have been making cutlery sets and kitchenware for many famous brands all over the world. Our team consists of hundreds of experienced and well-trianed technicians, so we can fast respond to customers' large quantity demand on high quality products.
- Q: The cutting surface of the optical fiber cutter is like this, what's going on?
- Carefully close the cutting knife to see whether the two sides of the rubber gasket is intact. If intact, carefully observe the top blade to contact fiber piece arc area not intact, then the level of direction was much higher than the top blade gasket, with a 1.5mm as a benchmark, try not to go down fine cutting. The time can shake head check guide rail wear, wear, cutting blade to promote instability, how to adjust is good, the general cutter is used in the IKO guide, should not be so easy to wear. Unless cottage.PS is now some cutting knife, fiber clamp is not good to put the bare fiber will be placed when there will be such an end face.This is the way I transferred, upstairs from the next should be better.
- Q: CNC lathe tool holder can not be reset after the knife to do?
- If you are unable to move the carriage to exit a and then try to use it to turn off the power first hand, or if not it may be burned (IF amplifier module in the boot state can rotate with hand screw it must be.). Look for an electrician, do not have to change the words.
- Q: Drilling out of the hole is the overall deviation, the hole is 0.15, the cutting tool angle is not biased, the product is not how to jump, I was the first drilling after the chamfer, is how to go wrong, in this case, ask the teacher, thank you first, urgent...
- Perhaps the clamping part is not strong, you look at whether the clamping, three claws excessive wear.Recommendation: 1 check the three claws.2 hydraulic chuck, increase pressure.3 chamfer first, then hit the center hole.
- Q: NC turret is not in place
- Holzer element and outer ring position are not good. Please check.
- Q: How to do the slide shoe
- Nails can be used as follows.Use a hammer to hammer the bigger one in the mouth, then screw it.In addition, there is a special tool for dealing with sliding wire. You can break a nail.Knife slide wire no way, can only change the tool holder. Even if the wire tapping to do the thread, the diameter is not the same as the original
- Q: In front of the turret with rear turret in the car to count the G41G42 cutter compensation when there is no difference?
- The turret of the numerical control lathe is the front knife holder in the operator's side.The common lathe is the rear cutter.When the tool head, the G42 tip radius compensation right bias in the car when the hole, when the car is round with G41.
- Q: What is the difference between the KSJ and HV
- Far, the accuracy of the KSJ knife, the quality is much higher than the HV, the price in that bad! But I'm talking about genuine
- Q: What is the tool rest
- DefinitionAuxiliary device for rotating workpiece with radial support. During machining, the workpiece moves axially along with the tool.Applied disciplineMechanical Engineering (first level), cutting process and equipment (two disciplines), metal cutting machine tools - metal machine parts (class three)
- Q: Is the plastic knife holder of roller skate good or metal knife holder good?
- It should not be adapted to the multi slip will be good at the beginning of the selection of a number of domestic imitation shoes cheap and durable more suitable for noviceC3 very heavy... Out of print now if the new shoes about 3000+ old words are not necessarily
- Q: Fanuc CNC lathe tool holder for maintenance
- Knife for the knife to stop, that is, the system can not find the knife bit number, not the hair is the encoder disk failure or line failure. In the FANUC system can be monitored on the I/O signal to identify the cause of the knife to turn around, and the cutter position signal is not a change, check the line, if there is a change, is the issue of the issue
1. Manufacturer Overview
| Location | Guangdong, China |
| Year Established | 2003 |
| Annual Output Value | Above US$6 Million |
| Main Markets | Northern Europe; North America; South America |
| Company Certifications | ISO 9001:2008 |
2. Manufacturer Certificates
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period |
3. Manufacturer Capability
| a) Trade Capacity | |
| Nearest Port | Guangzhou; Shenzhen |
| Export Percentage | 90% |
| No.of Employees in Trade Department | 300-500 People |
| Language Spoken: | Chinese,English |
| b) Factory Information | |
| Factory Size: | Above 5,000 square meters |
| No. of Production Lines | Above 6 |
| Contract Manufacturing | OEM Service Offered; Design Service Offered |
| Product Price Range | High; Average |
Send your message to us
Non-Stick Colorful Knife Set
- Ref Price:
-
- Loading Port:
- ShenZhen
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 sets set
- Supply Capability:
- 1000000 Set set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
