knife seat,F-KB043 Rubber wood knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
product name：rubber wood knife seat
material：rubber wood
MEAS：26*22*12cm
Specifications:
Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense
Excellent toughness, process into various curved according to the needs , full of beauty
Solid texture，manufactured goods with firm structure，prolonged service life
The texture of rubber wood is fine and closely woven，pore full of lots ot padding so it's hard to absorb water and corrode.
Description：
1、The knife seat use material of high quality natural rubber wood and take professional advanced machine equipment and manual binding.
2、The knife seat was refined by material, assembly, polishing, painting and other procedures.
3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.
4、Hoteam commerce co.，LTD，is a manufactory specialized in all kinds of wood knife handles，wood seats，chopping boards and other woodworks.
5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure that dry and clean and put it in the open air
Primary Competitive Advantages:
Brand-name Parts Country of Origin
Distributorships Offered Experienced Staff
Form A Green Product
Guarantee/Warranty International Approvals
Packaging Price
Product Features Product Performance
Prompt Delivery
Main Export Markets:
Eastern Europe North America
Mid East/Africa Central/South America
Asia Western Europe
Australasia
- Q: CNC lathe turret, sometimes why turn around.
- Open the end of the tool holder, there is a bad disk or water. The solution uses the hair dryer to dry, if it is not OK to replace.
- Q: How to distinguish the CNC lathe turret and turret turret after that car, belonging to the front tool or tool? Before the turret is cylindrical with G42 or inner circle?
- The turret of the numerical control lathe is the front knife holder in the operator's side. The common lathe is the rear cutter. When the tool head, the G42 tip radius compensation right bias in the car when the hole, when the car is round with G41.
- Q: Drilling out of the hole is the overall deviation, the hole is 0.15, the cutting tool angle is not biased, the product is not how to jump, I was the first drilling after the chamfer, is how to go wrong, in this case, ask the teacher, thank you first, urgent...
- Perhaps the clamping part is not strong, you look at whether the clamping, three claws excessive wear.Recommendation: 1 check the three claws.2 hydraulic chuck, increase pressure.3 chamfer first, then hit the center hole.
- Q: How to do the slide shoe
- Knife slide wire can only change the knife holder, if it is wearing a nail sliding wire, you can use the electric drill to wear the nail, remove the nail, replace it.
- Q: However, No. 2, No. 3, the normal use of potential energy on the knife No. 4 can not be normal use of the rotation has not stopped on the 1.
- 1-2-3 knife is normal? Can't you find the knife on the number four? The 4 line may be broken or bad contact!
- Q: What is the difference between the tool holder of the CNC machine tool and the horizontal lathe
- The biggest difference is the CNC machine tool you can use the T0101 1 knife knife No. 1. T0202 T0303 T0404And so on。 You have to use a hand crank on a horizontal lathe
- Q: CNC turret is also called the sender sensor
- No, the inductive switch is only one of the components of the sender. Each unit corresponds to a Holzer sensor, along with the knife on the knife body rotation, the switch will be close to the magnet Holzer signal. What is the location of the knife to tell the host. The white piece fixed on the edge is a magnet. The middle line is the sensor. Together, they constitute a communications disk.
- Q: GSK980TA CNC lathe tool holder how to move
- Behind three with the line for a try, if the impact of the knife should be a pin problem, open the adjustment OK
- Q: How to return to the ordinary lathe tool
- Remove and check whether the spring pin back position is smooth (with the hands of the press about 20 times). Take a look at whether the end of the spring pin has been seriously worn, the same knife bottom surface is also turned over to see if the limit groove is also serious wear.
- Q: Fanuc CNC lathe tool holder for maintenance
- Check the cutter line, replace the knife Holzer (send).
Send your message to us
knife seat,F-KB043 Rubber wood knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
