17 inches auto sport aluminum alloy car wheel rims

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1,auto wheel rim
2,saving energy
3, Our car alloy wheel has great competitive strength
4, low price
5, Standard:TS16949/IS2

BK409 auto wheel rim for a car

1,auto wheel rim

2,saving energy
3, Our car alloy wheel has great competitive strength

4, low price

5, Standard:TS16949/IS2002,VIA,.TSE and GMC

BK409
SIZE OFFSET PCD HOLE
13X6.0 +30 100-114.3 4H

My company produces and exports alloy wheel s for years with good quality and competitive prices. We offer the quality customize wheel for aftermarket as well replica wheels. We have the size range from 12 inches to 24inches. We can make the wheels as chrome or paint finish. We promise the prompt delivery and reasonable price. We have the capacity of 15,0000pcs per month . So we can meet the quantity you want. Welcome anybody who want to deal these products to contact us.Up to now, we have enjoyed good popularity all over the world.

Q: Chery A1 wading the wheel after the lock how the matter: According to your analysis of the situation, it may be because your vehicle wading after the rain is not completely drained, you stop, because the body of the brake drum into the water after the easy emergence of the phenomenon of hoof up, causing the rear wheel The This requires the 4s shop technician to take the tools to disassemble the tire to the site to remove the tires and brake drums, adjust the gap of the shoe, so that the spring inside the reset.

Q: So i bought a 1990 Honda Accord.The steering wheel is off to the right.So when im going straight the steering wheel is quite a bit to the right.It is not an alignment because i let go of the wheel and the car goes straight ahead. I need a free solution i can do myself. My father says i can take off the steering wheel(without a wheel puller) and put it back on straight and that should solve the problem. What do you guys think: Steering wheels are meant to go on one way, so the turn signal indicators will function properly. Obviously at one point, someone had this car aligned, and the shop did not set the steering wheel straight first. It can be remedied by turning the tie rods an even amount each, a little at a time until it drives straight and the wheel is centered.

Q: I saw the 3 wheel motorcycles, however I have my ninja 250 still (I plan on keeping it) What do you guys/ girls think? 2 wheelers or 3 and explain.: A 3 wheeler is not a motorcycle, when I am 80 I may want one.

Q: What do you call each of the different options on spin the wheel? Is there a general term for them?Thanks!: My wheels spin every time I pedal my bicycle. Cycling section is bicycles. I have no idea where your question belongs. But it's not here.

Q: is there any aerospoke wheels for a cyclocross bikesand is it possible to make a fixed gear cyclocross bike?: I don't see any reason why you couldn't use an aerospoked wheel for a cyclocross bike, I don't think there would be an advantage to it, most of the courses are short with not much open space for them to be effective. I would also be concerned about the edges on aerospokes. The dynamics of cyclocross, not that I get my hands or arms through the wheels, but spinning aerospoked wheels would hurt alot more if you did happend to put a finger, hand or arm near them. And I don't see any reason you couldn't set on up as a fixed gear, but i think it would make mounting and dismounting at obstacles a bit tricky. That's my two cents. . . Now, get out and ride!.

Q: Like the production of ladle wheels of this kind of parts are there good manufacturers? The: Application areas: brick, building materials, stone, railway logistics, aluminum, roads, sand, mine construction, equipment manufacturing, paper, energy, metal processing

Q: What‘s the proper way to measure the diameter of a car wheel? From all the way at the top to the very bottom or what?: The same way you measure the diameter of any circle, From top to bottom through the centre.

Q: *Two Wheels*One wheel turns at 33 1/3 revolutions per minute. A second wheel turns at 45 revolutions per minute. At some point in time, a mark on each wheel is at the lowest point on each wheel at the same time. What is the least number of seconds until the marks on both wheels are again both at the lowest point at the same time?Justify your answer and show all work!This is a problem challenge for school and it is very confusing. i have ideas of how to solve it but i‘m not sure how to go about it. This is for extra credit and due tomorrow, 10/24/07, so please try and solve this as soon as you can. Thank You!!!: This Site Might Help You. RE: 2002 Ford Taurus Transmission Rebuild Price? Saturday afternoon as we were driving down the street, my car suddenly stopped moving forward. We could press on the gas pedal, but no movement. After having it towed to the shop Saturday, we were informed today that the entire transmission needs to be rebuilt and were quoted $2293 to do it

Q: compare to the avalanche 4 wheel drive, what i really mean is what is the difference between 2 wheel drive and 4 wheel drive: 2 wheel drive really means, only one rear wheel is pulling. 4 wheel drive, at least one front wheel and one rear wheel are pulling for better traction

Q: im making a custom bike and want a small front tire could i use like a razor scooter wheelor maybe like a moped wheel or just a small bicycle wheelwhere would i be able to get one: Use a 12 1/2 pneumatic bicycle/scooter wheel. Pro bike shops usually have scooters with these types of wheels around, toddler bikes have the wheels on them. I recently bought a set of 12 1/2 Kenda tires and some Bell tubes, every bit the quality of larger ones for a friends kids Tonka bike. Also, in the late 80's early 90's when I was a kid there was slew of cheap scooters with mag wheels and pneumatic tires, but they were a pain in the rear to air up since they had so little rim to hub clearance. I'm sure you can find one of those locally at a pawn shop or junk dealer no problem, I think they were 8 1/2 x 2 or something.

Send your message to us

*Email

*TEL

*Quantity

*Unit