WQ Vertical Sewage Centrifugal Submersible Water Pumps

WQ Vertical Sewage Centrifugal Submersible Water Pumps System 1

WQ Vertical Sewage Centrifugal Submersible Water Pumps

Ref Price:

Loading Port:: Shanghai

Payment Terms:: TT OR LC

Min Order Qty:: 1 set

Supply Capability:: 100 set/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1. Specification For WQ Submersible Sewage Centrifugal Pump

1) CE,GS,ROHS,ISO9001.CC
2) With aluminium pump boby,anti-corrosion
3) Sewage pump
4) Dirty water pump
5) Water pump

2. Product Introduction for WQ Submersible Sewage Centrifugal Pump.
WQD WQ type submersible sewage pump/dirty water pump consists of pump,mechanical seal and motor.Pump is at the bottom part of motor pump,which adopt centifugal impeller. Motor is at the upper part of motor pump and is a single-phase asynchronous motor or three-phase motor.Mechanicalk seal is between pump and motor,and it'sa kind of double end mechanical seal."o"rings are applied to all static joints of the submersible pump.Inner-installed protector prevents the pujmp from damages due to abnormal power,colg and overload etc.

3. Working Condition of WQ Submersible Sewage Centrifugal Pump.
1) Transport liquid water temperature is less than +40°C
2) The PH value of the media is between 6.5to 8.5
3) The volume per centage of impurity in the medium is less than 0.1%,grain smaller than 0.2mm
4) Pump should be rated near lift the appropriate range,submersible pump head can not be too low,below the stiplated 80%of head easily lead to thermal protector,so that pumps stopped running,and even cause electrical damage.
5) Diving depth of no more than 5m.

4. FAQ for WQ Submersible Sewage Centrifugal Pump
1) Are CNBM pumps available in DIY stores?
Yes, currently, we’re available for DIY stores all over the world.
2) Where do I have to send pumps for service?
You must send them to the CNBM PUMP Service Point or, after contacting Customer Care, to the CNBM PUMP service center in China.
3)Are your pumps acid-proofed?
To choose the right pumps for chemical applications, we do need further details on hydraulic operations as well as on the type, concentration and temperature of the liquid.

WQ Vertical Sewage Centrifugal Submersible Water Pumps

Q:Water pump does not produce water, what are the reasons?: 6. is the motor running in correct directions?.7. pump body failure, such as sliding off the leaves or too much gap between the mouth ring.

Q:Direct connection pump What is straight pump and non direct pump? What's the difference in structure?: Direct connected pump: pump impeller installed directly on the motor shaft, it looks like a whole, relatively compact, simple installation, but the general power is relatively small (big bad processing connection, but not absolute);Non direct pump: pumps and motors are independent of each other, through the coupling torque transmission, the structure is relatively large, complex installation, to adjust the level / concentricity and so on, the general power is relatively large

Q:What is the lift of diaphragm pump?: Tell you: diaphragm pump head is liquid through the pump energy obtained is called lift it, and flow and pump speed, a liquid density is generally 1 kg is 10 meters lift, horizontal pipeline 10 meters 1 meters lift, a 90 degree bend is 1 meters.

Q:What do you mean by the self coupling device on the pump?: Overview of GAK self coupling device:The utility model relates to a GAK self coupling device, which is an automatic butt joint between a water outlet flange of a submersible electric pump and a water outlet pipe system.In the above additional coupling flange and the water outlet pipe seat inlet flange with a pair of wedge card, under the additional coupling flange and the water outlet pipe seat inlet flange and a pair of wedge cards in a wedge seat below the outlet pipe inlet flange card is made of elastic steel plate is fixed on the lower side of the seat pipe inlet flange. When the submersible pump water falling from above, Kaxianka additional coupling flange at the top of the wedge wedge and seat card outlet pipe above the inlet flange together, in the role of the dignity of the pump and submersible inclined wedge clamp, two flange will be put together in a pair of wedge under additional coupling flange and the water outlet pipe seat inlet flange the card will be in the elastic plate under the action of automatic card together. The utility model can solve the problem that a large amount of water leakage between the two flanges of the coupling is saved when the automatic installation and disassembly of the electric submersible pump is convenient, thereby saving energy.

Q:Why can the centrifugal pump hold down the pressure?: The pump before starting to pump shell and the water pipe filled with water, and then start the motor, the pump shaft to drive the impeller and water do high-speed rotation, centrifugal water movement, was thrown to the outer edge of the impeller, the pressure water pipeline flow through the volute pump into the pump shell.

Q:What does "efficiency" mean in a water pump catalog?: General pump efficiency is 60% ~ 85%. high efficiency of the pump, indicating the same work, the pump consumes the lowest energy, and vice versa

Q:What are the starting and stopping procedures for centrifugal pumps?: The use of centrifugal pump can be divided into three steps, namely, start, run, stop.Start: you should do the following preparation before starting:(1) check the water pump equipment in good condition.(2) the bearings are filled with oil, the oil level is normal, and the oil quality is qualified(3) all the inlet valves of the centrifugal pump are opened.(4) pump water injection or vacuum pump diversion (except for flow), open the vent valve exhaust.(5) check the leakage of shaft seal. It is advisable to fill the seal with a little drop of water.(6) the motor rotates in the right direction.

Q:Types and differences of pumps: Classification and working principle of pump by structureClassification of pumpsInvolved pump standard product types are also very much, a centrifugal pump, metering pump, screw pump, reciprocating pump, hydraulic pump, submersible pump, oil pump, water pump, pressure test pump, vortex pump, cryogenic pump, vacuum pump, roots pump, molecular pump, gear pump, mud pump, corrosion-resistant pump deep well pump, water pump, mixed flow pump, axial flow pump, boiler feedwater pump, liquid pump, injection pump, chemical pump, pump plugging and no leakage pump, plastic pump, fire pump and so on, there are many. Its name is divided according to some conventional classification methods such as pump vane pump volume, pump etc., some are divided by purpose such as sewage pump, pump and other health, some names are more random as diffusion pump, liquid nitrogen pump. As long as the production of this product, with standard requirements, through a certain application and approval procedures may produce a new The standard, but sometimes the content also has a repeated cross, quite. The domestic and foreign standards, the domestic standard is more than the number of foreign standards. In general, such as centrifugal pumps are widely used, the production history of the pump more standard (total standard centrifugal pump up to more than 100). As new standard pump leakage pump this rapid development is relatively small. This paper introduces the structure and working principle of the pump according to the classification of the

Q:Rules for operation of centrifugal pumps: 3, start the pump, wait until the speed reaches the normal speed, slowly open the outlet valve, observe the ammeter at the same time, and control the current in the rated current range of the motor.4, the operation requires smooth operation of water pumps, no abnormal noise, no pressure fluctuations. The abnormal situation should be stopped in time.

Q:What flowmeter is installed after the pneumatic diaphragm pump?: The pressure decreases, the diaphragm moves slowly, and the flow decreases.This is not particularly accurate, because the diaphragm is not a metering pump, but the approximate flow can still be controlled.

1. Manufacturer Overview
Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range