Standard Hot Dipped Galvanized Wire 2.0mm

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Commercial Galvanized Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

(7) Zinc Coating

Meet GB/T 15393 standard.

Q: would the wiring harness on a 1.8 acura integra engine fit a 1.6 honda civic harness?: i've got not got the coolest comparable form jeep, even even with the shown fact that it particularly is terrific to attempt the wreckers, they continuously have spare areas, in the event that they have not got it, then ring Jeep up and ask them in the event that they have a spare one, there low fee.

Q: Any instructions on how to make rings, necklaces, and bracelets out of colored telephone wire.: We okorder /

Q: I have a set of pilot wi-200 strobe lights and they have three wires and i want to hook them up to a optx headlight strobe control module the wires are gray white and black can you tell me where to hook them: I wouldn't try it. The gray, white, and black wires are the high voltage strobe wires. The control module changes the patterns before the voltage is increased. There is nothing you can do here.

Q: i want to attach a wire to my new speaker but when i cut the wire taken from my headphone, there are 4 wires in it, 2 are golden colored and the other two are green and blue but the speaker has only 2 points to connect the wires.Someone plz help me.: Just get some speaker wire its not that expensive ; go to Wal Mart where they have the TV's and ask for speaker wire or go to the hardwear store and ask for speaker wire or lamp cord thats polorized for the wire you have twist the two golden wires together at both ends and twist the blu and green together at both ends now use the golden for positive and the other for negative.....

Q: I did an engine swap with some friends and everything is in place, from the rebuild 700R4 w/ a shift kit, to the rebuild 350 bored .30 over. But all I have left to do is the wiring, but have no idea how to. So about how much would it cost to have a professional finish the wiring?: The wiring on a basic carburated non emissions engine is pretty basic...it's something you could do by yourself in your garage. Anyone that has any knowledge in wiring and electricity could wire it up. Don't let it scare you! :)

Q: How do you wire an electrical outlet and light switch in a bathroom? Box is existing, wires existing.: The first trick is to identify the wires. White wires will normally be neutral; there will be at least two colored or black wires, one of which will be the hot supply wire. Use a neon tester ($2 at a hardware store) to idenify which. If all of the white wires were tied together, then the switch will simply connect the two colored wires to each other; brush these together to verify that the light flashes. Now turn off the power at the breaker box. Connect the hot supply wire to a brass screw on the outlet, and attach a 6 piece of black wire to the other brass screw. Connect the joined white wires to a nickel-plated screw (you may need a wire nut and short piece of white wire to do this). Connect the short black wire to one of the screws on the switch, and the existing black wire to the other screw. And that should do it. Note that a double-width box is necessary for this. Code requires that a GFCI device be used in all bathroom outlets. If there is not one in the breaker box servicing the line to the bathroom, you should use a GFCI outlet device (about $12) rather than a conventional outlet. You can get a cover plate to match.

Q: Why would I want to upgrade the wires on my airsoft gun? What does it do?: cheap wires tend to break over time, short out, etc. It's nice to have quality stuff in you gun.

Q: I've seen people use it as ...umm..energy generating...majiggy.. (but not alot of energy) including a magnet/something about a magnetic field or some sort?and instead of MAGNET WIRES can i use SPEAKER WIRES?(RADIO SHACK): Magnet wire is just solid copper with a layer of varnish for insulation. Speaker wire would work, but you could not wind the wire as tightly due to the thicker insulation. also the wire is very flexible and will not stay in place very well. Also, if the coil gets hot, the insulation on the Speaker wire will start to burn or melt. .

Q: 2.4) A wire has a resistance of 19.2 . It is melted down, and from the same volume of metal a new wire is made that is 5 times longer than the original wire. What is the resistance of the new wire?: .4) A wire has a resistance of 19.2 . It is melted down, and from the same volume of metal a new wire is made that is 5 times longer than the original wire. What is the resistance of the new wire? Resistance = ρ * (L ÷ A) ρ = resistivity L = length A = cross sectional area L * A = volume of wire. The volume is constant L1 * A1 = L2 * A2 It is melted down, and from the same volume of metal a new wire is made that is 5 times longer than the original wire. Since the length is 5 times longer, the area is 1/5th of the original volume Resistance2 = ρ * (5L ÷ 0.2A) = ρ * 25 * L/A The new resistance is 25 times the original resistance = 25 * 19.2 = 96 Ω

Q: how do you hook up a wired connection with xbox 360 if you have an wireless connection(the wire included with the 360): the 360 has a wireless adapter option, the ethernet cable is only for wired modems not wireless routers

Send your message to us

*Email

*TEL

*Quantity

*Unit