Single core concentric cable for rated voltage up to and including 0.6 / 1 kV
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 30000 m/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Product Introduction:
Concentric conductor cable is suitable for rated voltage up to and including 0.6 / 1 kV and is used to supply a transmission.Cable and even less positive sequence (negative) and zero sequence impedance, this which is beneficial for improving food quality. Concentric conductor layer is smaller than the reactance value of the fourth ordinary four core cable to the basic state of the zero sequence, which is useful for short-circuit protection device of the automatic responsive action so to ensure the safety related equipment.Cable cable has a high resistance to interference resistance characteristics and electromagnetic lightning.
Operating characteristics:
Conductor: Alumunim or Copper
Insulation:PVC or XLPE
Inner covering: PVC
Outer sheath:PVC
Rated Voltage: 600/1000V.
Specification:
Rated voltage | 0.6/1kV |
Max.permissible continuous operating temperature of conductor | 90°C |
Installation the ambient temperature | ≥ 0°C |
The bending radius of Non-armored cables | ≥6 times of cable diameter |
The bending radius of armoured or copper-tape-shielded cables | ≥12 times of cable diameter |
- Q: I have a power adapter that goes to a mixer (Denon DN-MC6000) and reads: INPUT 100-240V ~ 50/60Hz 1.5A, OUTPUT: 12V - 3A. Now I know this is the right adapter but I don't know if I have the right cable that goes from the adapter to the wall. I have one that says 6A 250V~ but I dunno if its the right one. I have a few others but can someone tell me what will be the right one so I don't blow up my mixer :P thanks
- This type of power cable can be plugged into any household power between 100 and 240 volts. So, any plug that fits into the wall plug is the right one. In the US and Canada the voltage is 110-120 volts. In the rest of the world 240 volts are used The plug and wire you mention is for the rest of the world. Now look at the adapter where you plug the cable into. Do they fit together? If yes go for it. If not keep looking.
- Q: I have an Eclipse SW9102 (101500 Watt Max, 750 W RMS, Dual 4ohm Voice coils) and I'm looking to buy an amp kit and amplifier. How big of an amp do I need and does it matter if its too much power? I'm looking at the SSL F2.2000 FORCE CLASS 2000W amp on OKorder as cost is a big factor in my setup. The OKorder link says:Max Power @ 2 ohm 1000W x 2 RMS Power @ 4 ohm 350W x 2 Bridged Power 2000W x 1 2 ohm stable in stereoIs this too powerful for my subwoofer? I've read that my sub can take more than it says but I don't want to risk it and I probably won't have this at full blast either. If I bought this one how would I wire it as I only have one sub?....would bridged be 4ohm 1000 Watt RMS x1?Also, what kind of amp installation kit should I buy? A lot of the 4 guage kits say they are rated for different maximum wattage. Are they actually different or can all 4 guage kits handle the same?Sorry I'm a noob! Thanks in advance!
- Hey okorder /
- Q: I have a 2003 hyundai tiburon and need to know where in the firewall should i drill my hole to run the power cable i know it goes throught the firewall but where if you have ever done this to a tiburon please let me know.
- you should see a hole in your firewall with wires going through already. pop your hood an look where theyre coming through then go inside and locate the hole.
- Q: will leaving the power cable in for my laptop hurt the battery?
- No, I've always done that with no issues.
- Q: Ok so I was doing something stupid just now. Cuttiing a power cable that connects to the tv. Halfway through to cutting it, the wire explodes and hit my face o,o. So quickly, I turn all of the switches off and run to wash my face. I just wanted to know whether it's ok to turn all the switched back on cus I'm literally in the dark right now. And will there be any damage to my face since the wire explodes in my face?
- Everything will be fine to turn the switches back on, but you must unplug the cord you were cutting first. If not, you'll hear another loud pop as the breaker switches off. Unplug the cord, then turn the switches back on. Before you plug the tv in, check the cord going to it for burn or charring. If you do not see any, then stand to the side of the tv away from the screen and back, and then plug it in. Be careful. Unplug the cut cord first!!!
- Q: I blew 2 fuses in my amp in my car, i have replaced them both, one was a 30amp and the other a 20. The 30 amp was an inline fuse from the battery to the amp and the 20 amp was a standard 20 amp fuse in the amp. As i said i replaced both fuses and try the amp again and it wouldnt go. There is a LED light on the top just lighting up a logo, when i attatch the power from the battery the light goes off and when i disconnect it the light comes on. When i dissconect the power the red light for diagnose comes on.
- This sounds like a wiring problem i reccomend you completly inspect all wiring to your amp if looks fine then use a test light and test all the wiring if all passes then your problem is within the amp itself. test the remote wire with stereo to car on if wired that way.
- Q: im looking at installing an amp and was wondering if its fine to go through the firewall were there is already a group of wires with a rubber seal, i was thinking of poking a hole through the rubber seal and running the power cable through there would this be a suitable option. Thanks
- Of course you can. As many amps that I have installed I have only had to drill one hole through the fire wall. As long as there is a grommet you are good to go. You should be able to open the rubber up with a screw driver. Just be careful not to damage any wires.
- Q: remove just this cable or use different hd and it works fine, is the hd broken or is it a power consumption by the hd issue? tryed a different psu and its the same problem, unfortunately not got another pc handy to check the hd on. Thanks In advance?
- change the hdd interface bus u may get solution otherwise replace it. .in
- Q: I got a free graphics card from my cousin and my computer only has the SATA slots for graphic cards and the one he gave me has the 4 Pin cable. Is there anyway to get it converted or any cables that can go from 4 Pin to sata? I wanna see how this graphics card goes when its working fully.
- Sure you don't have any molex connectors at all? Not even in your DVD drive? If so, get a Y adapter with a good amount of length. If not, then look for an adapter. Be careful as the vast majority are to convert a molex power cable to a SATA power connector, not the other way around. In the worst case you could hook up a separate power supply to it.
- Q: And if so how much would that cable be and could you supply a link to get it from that place?Im really struggling to find any details of where i can get one so could you possibly check out the item and see if there is any help on there?I currently have a 3A 250v Power cable and i'm wondering if that can help?Thanks alot and if it helps ill pick a best answer soon. Thank you!
- High input cable ...? Not really sure what that is, Also, that power supply is junk. 750W and it only has a single 6-pin PCI? That's sad. Good 750W power supplies are at least ?70 and have four 6-pin PCI cables. Heck, a good 430W costs more than that and it's guaranteed to perform better.
Send your message to us
Single core concentric cable for rated voltage up to and including 0.6 / 1 kV
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 30000 m/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
