PVC Coated Welded Mesh

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Packaging Detail:	in carton box PVC Coated Welded Mesh Panels for Mink Cage
Delivery Detail:	20 days PVC Coated Welded Mesh Panels for Mink Cage

PVC Coated Welded Mesh Panels for Mink Cage
1.Size:910*450mm
2.Material:carbon steel
3.color can be available.

PVC Coated Welded Mesh Panels for Mink Cage |Wire shelf mesh display panel | chrome wire shelf I plastic coated wire shelving.

Product Description

Ref No.	WS-003
Size( LWH )	910MM*450MM
Material	carbon steel
surface treatment	zinc/chrome/powder coating
note	size and color can be available for the customer

Q: I just removed a Australian light switch that I've never seen before that controlled a bathroom ceiling fan and the bathroom light. (both buttons on a single panel switch)I have a black wire coming from the switch box that has 2 other black wires splitting out from the connection point, one of each going to the fan and the light. And a single black wire going to the ceiling fan and a red wire to the light.I'm just putting in your everyday off/on switch one for each the fan and the light. any help? what are the positive and negative wires?: The one that has a flat is the negative the one that has the bump is the positive! Hope i helped!

Q: I am replacing an electrical outlet that currently has 3 white and 3 black wires plus the ground wire. The bad outlet has 3 holes already in it for each of the wires but my new outlet does not, there are only 2 holes and/or the 2 screw on each side. How do I install this new outlet? Do I need to do the pigtail here?: How To Replace An Outlet

Q: Ceiling fan has a black wire, white wire, green wire and also a black and white wire.: The white wire from the fan gets connected to the white wire (neutral) in the ceiling box. The green wire is ground. It is connected to the fan mounting bar where the bare copper wire is connected. The remaining two wires are your hot wires. One goes to the fan and the other goes to the lights so you can run the lights on a dimmer circuit. I believe the black is for the fan and the black-white is for the lights. Your fan's instruction manual should identify these wires. IMPORTANT: Never run the fan motor on a standard dimmer. A dimmer is designed for use with resistive loads like incandescent, halogen, and (to some degree) LED lamps only. Running an inductive load like a fan motor will create noise spikes on your electrical circuit and possibly overheat the motor causing premature failure.

Q: how do i tap a speaker wire? car audio not really my department: RE: Why Monster XP speaker cord sounds worse than production facility speaker cord? purely put in Monster XP speaker cord to all my Onkyo audio gadget and now its lots softer than the speaker cord that got here with my Onkyo receiver. quantity was once at 25-35 and it grew to become into loud and sparkling. Now after the Monster XP cord, I would desire to crank the receiver to approximately 50-60 to get the comparable sound...

Q: the charger has three wires to put a male plug on and they are black white and green and they look like 12 gauge wires: wire colors are green is ground the black and white wires are you load wires look at you 240 volt plug and determine which terminal is the ground this one is where the green wire goes the black and white wire go to other two terminals this should do it

Q: In the ceiling is one black, one white and a ground. How do I connect a new ceiling fan to these two wires? The ceiling fan has black wire, white wire, a blue wire and a green wire. We don't have green in the ceiling nor do we have a ground...knob and tube perhaps? So, can we connect this fan or not?Thanks!: White to white, black and blue to black, green to box.

Q: I just tore my old shed down, that was wired for electrical. though I never used power out there There is size 10 wiring (two wires), running from the house to where my shed was. I then bought a Tough Shed from The Home Depot and put it where my old shed was. While working on wiring my new shed for electricity, I turned power off to the entire house.I am trying to install power to the shed and I spliced the size 10 wires to size 14 (three cable, includes a ground) which I have connect to an electrical outlet in the shed, but once I turn the main power box back on, the circuit that runs power to the shed keeps tripping off. Am I missing something here?Thanks: Thats big # 10. Sounds like somebody was running a welder or air compressor. But you can still use it. Do Not forget your GFCI outlet.

Q: My boat came with a rule 500 2-wire auto pump. I have an on/off switch at the console. My replacement has 3 wires. How do I connect the 3 wires and still use my on/off switch?: Good after I used to be within the navy, electrical energy was once three phase. There was once no original. Considering the fact that its is a pump, my recommendation is disconnecting the pump out of your load. Go ahead and wire up your pump inserting the 3 wires on any terminal. If the pump rotates in reverse, stop the power and swtch any 2 wires and you are good to move.

Q: What's the metal wire fabric?Such as title: Metal wire fabric not only has metal luster, and wear to trim visible, noble, gorgeous, and the fabric has the function of conductive shielding, which is widely used in scientific research, military and medical industries such as electronics, high-tech, high added value.Currently do men and women's windbreaker, jacket, jacket and jacket.