Hot Dip Galv. Wire

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Commercial Galvanized Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

(7) Zinc Coating

Meet GB/T 15393 standard.

Q: I'm replacing the ground wire in a chandelier because it has been cut by the previous owner when it was removed from the ceiling. Overall it is pretty simple and I have everything diagramed. When I went to Radio Shack and bought the replacement wire they gave me 18 gauge solid insulated hookup wire. It looks totally different. The ground wire is a braided copper wire (7 strands). Should I go back and take my copper wire with me and get copper or is what I have just as good? An electrician will do the installation of the chandelier into the ceiling.: The reason they use copper as it does not corrode...

Q: I moved into a home with pre-wired speakers. There is a bundle of speaker wire coming out of the wall. Each wire has 4 colors of other wire coming out of it. There are a total of 7 main wires (with four wires each) and a total of 9 speakers.: 4 conductor wire has a few neat uses. 1 is to bi-wire your speakers. Meaning that if the speaker has 2 red and 2 black terminals then remove the bridge and run the cables to the posts separately thus increasing surface conduction and increasing output and sound quality. Also if you are running cables in the wall to 2 speakers that are near each other or to a single stereo speaker then you don't have to run 2 separate 2-conductor wires. This would also be true if you are running to a second zone using an in wall volume control. If this is the only wire you have for a standard speaker connection it won't hurt to twist them together at both end (pos with pos/ neg with neg) and serves the same purpose as using thicker cables.

Q: I have a set of pilot wi-200 strobe lights and they have three wires and i want to hook them up to a optx headlight strobe control module the wires are gray white and black can you tell me where to hook them: I wouldn't try it. The gray, white, and black wires are the high voltage strobe wires. The control module changes the patterns before the voltage is increased. There is nothing you can do here.

Q: I'm trying to fix a light fixture for a friend. Her father-in-law gummed it up. At the fixture, there are 3 white wires soldered to a single wire. There are 3 black individual wires and one red wire. There are three switches that control the light.If I hook one of the black and the 3 white to the light, the light stays on constantly. If I hook either of the two other black individually, nothing comes on period.I'm pretty much at a loss. Any advice would be greatly appreciated.: the white wire is neutral and hooks to the white on the light the black wire you had hooked when the light stayed on is the feed wireit hooks to either the other the other red or one of the black wires depending on how the switchjes are wired. i would try hooking the feed black to the red and the other 2 black to the black light

Q: i just got guitar hero 3 and i want to buy another guitar contoller for the xbox 360 but my mom only wants to buy the wired one because it is cheaper is there anything wrong with the wired one and should i get it or not since i will be playing it with my brother. also how long will the wire be.: dont get wired get wireless much better P.S. the wires arent very long

Q: electrical wire prices: It follows the copper market. During high economic growth periods, copper (for wiring) oil for fuel are both simultaneously in high demand.

Q: I am getting these 2 CVR 12's 4 ohm dvc and i am wiring them for a 2 ohm load (parallel). When you run a wire from voice coil 1 positive to voice coil 2 positive, then to amp. and the same for negative, what is the wire that is connecting the voice coils? is it a power wire, ground wire, speaker wire? please help!: This one is the terrific capacitor. Pyramid CAP300DBL 3-Farad extreme-overall performance digital skill Capacitor Technical info - 3 Farad Surge - Polished metallic end - Platinum-Plated sturdy Brass Hardware - computing gadget controlled On/Off - digital Voltage exhibit

Q: What causes signal Loss and Distortion in Copper Wire?: the resistance of the wire itself can be responsible for signal loss. electromagnetic fields may cause distortion. Another possibility is if the signal is not terminated properly you may experience a reflection of the signal traveling in opposition of the desired signal. Heat can cause loss or distortion. corrosion on the copper wire may also cause loss or distortion of the signal.

Q: The question is can i complete a ac circuit if i connect a live from one wire to a neutral from another.: yes you can but what you're asking doesn't sound safe! be sure you know what you're doing before you electrocute someone or burn the place down!

Q: What is a wiring harness?: For the best answers, search on this site https://shorturl.im/axbZn Buy a couple feet of 16 gauge THHN wire and some crimp-on butt splices. Use a wire crimper to strip the short wires, and butt splice a few inches of the new wire on to the short ends. Then connect the new wires to the harness. ACE hardware should have everything you need. An auto supply house might also.

Send your message to us

*Email

*TEL

*Quantity

*Unit