Highly valued Black Anneal Wire
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
| |||||||||||||||||||||||||||
- Q: What would the wire size be for a 3 phase 4 wire - 480/277V - 400A panelboard. Would it be (3) 600mcm w/ (1) 1/0 ground?
- Well not quite: 1. The panelboard is 4 wire therefore the (3) in the description would be (4). The 4th wire is for the neutral and required if you are using the 277. Otherwise the panelboard is a 3 wire board and no 277 2. 600 kcmil copper with 75°C insulation is able to carry 420 A as long as the ambient temperature < 86°F (30°C) and are installed by themselves (not in a raceway/cable tray with other power conductors). If the conductors are aluminum, the temperature is hot, the installation has multiple conductors in the same raceway/cable tray, or the distance is of sufficient length resulting in unacceptable voltage drop, the cable must be derated -- read you must increase the size to 750 kcmil or increase the insulation rating to 90°C The ground conductor should be of sufficient size
- Q: What are the advantages and disadvantages of a bank wire transfer ?
- Wire transfers on average will run you $15 for domestic and $30 for international. Both representatives from two different banks will process the electronic transfer. Advantage - No physical cash is exchanged. The money will be at another institution the same day. Disadvantage - Fee
- Q: How do you attach light wires to boat trailer frame?
- There are a couple of safe ways to attach the wires. First is to run the wires through the inside of the frame rails. this protect the wires from abrasion and from being cut, pinched, or severed easily. The next best is to get a bunch of Electricians Zip Tie mounts. These have a sticky foot so that they can be mounted anywhere. Then you install small ZIP ties into the slots and form a loop. Run the wires through the loops to where you need them to go. Once you have the wires placed and connected, snug up the wires and clip off the extra ZIP tie and work toward the front of the trailer doing the same as the last. Once you reach the tongue of the trailer, be sure to leave plenty of wire for the connector plug to the tow vehicle (usually about 4' beyond the coupler). Then your done.
- Q: I have a 2000 Subaru Outback, and I can get the thing working, but it does not save any of my settings. i know its my accessory wire because the radio will not turn on from any other wire.. soo help please
- There are two wires that you must hook up. One is for continuous power so that the settings are saved, the other is for power to the radio. If you had purchased your equipment from Crutchfield, you would have gotten free installation instructions and a wiring harness that would hook directly to your Subaru wiring - saving you a great deal of time and trouble.
- Q: I have a 99 Dodge Ram.. The radio ignition wire is burnt out.. Can anyone tell me where I can connect a new ignition wire to??
- Radio ignition wire? Could you be talking about the RFI capacitor that looks like a condenser? If it is it hooks to the hot side of the coil. I would need more information to properly answer this question.
- Q: Im cleaning up some of the wires in the engine bay and getting rid of ones i dont use. Right now theresthe pos side bat post runs down to the starter. From the starter there is a thicker wire and a skinny wire. In the thicker wire there is a wire that goes to the post on alternator. Both wires from starter run over to a relay maybe ithas a stud sticking out and has a wire that goes from the bottom of it to the fuse box. Im in middle of relocating the battery into the trunk so what wires can i eliminate and what wires have to go,to the battery?
- Like Mikey reported for starter and alternator it is not appropriate. in case you think of issues have been swapped there are various strategies over the 40+ years that Chev made the classic small block. Assuming that's a Chev motor there are in basic terms 2 starters and the version is the place the mounting bolts are. One version the bolts are in the present day for the time of from one yet another and the different form they're offset. most of the engine blocks have the two contraptions of holes so it relies upon on the flywheel which one is needed. Alternator could be slightly extra challenging to verify. countless strategies will bodily in superb condition then you definately've the pulley form, connector type and charm and orientation. you will be able to ought to snap some pictures and desire for an surprising guy on the aspects save or carry the previous one in and tournament it up.
- Q: To help clean things up and make wiring a little more simpler on my jeep i got a fuse/relay box off an old junk car. i want to wire my off road lights into this relay box but i'm not sure what size wire is in the box it appears to be either 18 or 16 AWG one place said to strip the wire and measure the wire another says measure in the insulation. i'm not sure what to do. but if it is 18 awg would it hurt to go to a bigger size after the fuse box to my lights or should i rewire the whole box?
- For okorder /... Wiring gauge always specifies the diameter of the WIRING not the insulation, since the insulation thickness can vary. You would have to strip the wire and measure the bare wire with a gauge. You can also look at the printing on the insulation for the gauge. Look for something like AWG 14 etc. You can buy a standalone headlight harness that contains the relay and wiring for aftermarket lights. I would recommend running both positive and negative wires all the way to the battery for maximum current.
- Q: How are wired differ from wireless doorbells,next how are they installed and finally the cost of them?
- Wired have a wire that connects the button near the door, the transformer, and the chime. When the button is pushed, the transformer energizes the chime, causing it to ring. You, or an electrician, must fish wires to a location where a transformer can get a constant supply of power, such as an outlet. There also need to be wires fished to the chime and the button. Wireless work with radio waves. Costs vary widely, depending on the setup you go with. Decent wireless units start around $35-40, and go up from there. New chimes for wired systems start around $8 and up. Transformers start at $10, buttons start around $5. Hope this helps.
- Q: Why would I want to upgrade the wires on my airsoft gun? What does it do?
- do no longer replace something in simple terms purchase a gun with a metallic gearbox, i comprehend i sound harsh yet your in simple terms dropping your money by using changing the full finished gearbox on a bad externally and internally gun.
- Q: Why do some vehicles have more than one starter wire at the ignition switch?
- The extra wire activates the fuel pump while cranking. The run position only lets the fuel pump run if it sees signals from the cam and/or crankshaft sensors.
Send your message to us
Highly valued Black Anneal Wire
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
