High Quality PVC Coated Wire

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Place of Origin:	China (Mainland)	Certification:	ISO9001:2008	Model Number:	PDB-3
Surface Treatment:	Coated	Type:	U Type Wire	Function:	Binding Wire
Wire Gauge:	BWG8-BWG22	Place of origin::	Hebei China	Raw material::	Q195
Surface treatment::	pvc coated	Coated material::	high quality pure pvc	Pvc color::	dark green ,light green, blue ,red, white, yellow, grey, etc.
Inner wire::	galvanized wire ,black wire ,etc.	Wire diamter::	0.5mm-5mm	Wire gauge ::	BWG8-BWG24
Payment Terms::	L/C,T/T

Packaging Detail:	0.5KGS-1000KGs per coil. wrap with plastic film, Hessian cloth or moister-proof paper.
Delivery Detail:	20 days after received the deposit or customized.

1.Purity raw material with ISO 9001
2.Surface:pvc coated
3.Inner wire diameter:0.8-4.0mm
4.OEM service with fast delivery

Q: I am trying to replace the window switch for the driver side and forgot the order of the wires. Can anyone hlep me.: Check out the link below. This is actually for the replacement of the window motor for the 4th gen. f-bodies. But, it does show picz of the switch and the wires leadin to the switch. Good luck!

Q: wire diagram and manual: a small boats wiring cant be very complicated. If you're needing to replace it get a book called Small Boat Wiring or a similar. If you're trying to find a fault with existing wiring simply trace the existing wires remake all the connections as you go. I suggest you pull the lot out redo it properly. Except for the electric start you dont need super heavy cabling for a small boat. Tinned multi strand wire with a core diameter of about 2 mm is fine. Get a roll of red one of black ( or use red/black figure 8 cable) From the battery fit a service fuse of about 15 - 20 amp in line with the positive cable right near the battery. Use only properly crimped screwed or soldered connections. If the connection is ever likely to get wet then cover the connection with a piece of heatshrink tubing with a good smear of neutral cure silicone inside it. The silicone should squeeze out both ends of the tube when you shrink it. Dont make any joints mid run ( never in the bilges). Make sure the wiring is secured where it is out of the way is neat. Support the wire near the connections. Run from the switch panel to each item as a separate circuit, dont daisy chain. Give each item its own cable including the return (black wire) brought back to the panel. Be neat make a permanent record of what you've done. Fuse each circuit with a fuse rated about 50% above what that item should draw. Always carry plenty of spare fuses.

Q: Where is itI have a 1996 Honda Accord with a pioneer deh-p6400 head unit. I tried to install an amp. Held the ground to soem metal and tried to get it to turn on. I tried the power antennae wire and it didnt' work. Nothing seems to work. I dont want to splice any wires or anything: hes right....all u have to do is continue the blue/white wire to the remote spot of the amp.

Q: well i've been asking for quite sometime on the correct wiring of a bathroom fan up to the same circuit as my light in the bathroom but i believe i've figured out. but i have a question now about the wire guage.the wire guage in the house is the standard solid 12 or 14 i think(house built in 50's) and the the wire that came with the bathroom fan looks a little smaller or about same size but it's braided .it should be fine to splice the two right?: It will be fine to wire nut them on there.

Q: im gettin a amp and sub for my car and was wondering how would i make a wiring kit for it ... i have basic knolage of wires but thats about it thanks in advance: the wiring kit is usually: - low gauge cable of certain length (x2) - rca cable of a certain length (x1) - small power connect cable (x1) seeing as these things are already pretty much in their simplest form, I don't see the practicality of making your own wiring kit. just buy one.

Q: hi i recently installed new plug wires into my continental should i put shieldings on them?: depends on what year the car is.did your old wires have shields?

Q: How do I wire with reg 5 wire T-Stat Installing a 2 ton Goodman A/C cond unit to a old Carrier Heat pump AHU with emergency heat strip.: depends on the t stat look at the back for a better idea the wires should be collor coaded 2 for the heat and 2 more for the ac and maby 1 for a ground

Q: Two steel wires are stretched with the same tension. The first wire has a diameter of 6.00E-4 m and the second wire has a diameter of 8.90E-4 m. If the speed of waves traveling along the first wire is 53.2 m/s, what is the speed of waves traveling along the second wire?: Wave velocity v = √(T/μ) Same tension in both wires: T1 = T2 μ is the linear mass density v1 = 53.2 m/s v2 = ? = v1/v2 = √(T1/μ1) / √(T2/μ2) = √(T1μ2 / T2μ1) = √(T1/T2 * μ2/μ1) = √(μ2/μ1) Linear mass density is mass/length, mass is density*volume: m/L = ρV/L = ρAL/L = ρA = ρπr^2 Both wires are steel so their density is the same. == v1/v2 = √(μ2/μ1) = √(ρπr2^2 / ρπr1^2) = √(r2^2 / r1^2) = r2/r1 == v2 = v1r1/r2 = (53.2*3.00×10^-4) / 4.45×10^-4 = 35.9 m/s ---- Speed of waves along the second wire is 35.9 m/s

Q: when u first get braces do they put the bands and the wire or just the bands cuz im getting them monday: You get the brackets with bands and the wire. Rubber bands, though, come later.

Q: ok got the mute wire figured out thanks to yahoo answers people..now i was wondering what the [ ILL] WIRE IS FOR ,ILLUMINATOR FOR SOMETHING?..also which wires on the speaker wires are pos and neg one is solid ,one is solid with stripe..not sure which is pos or neg thanks alot steve: first answer is correct, However, as long as you keep the solids and stripes consistent, it doesn't really matter if you hook them up negative stripe or positive stripe...just keep them all the same..

Send your message to us

*Email

*TEL

*Quantity

*Unit