Enameled Aluminum Wire for You

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

1.Product Description:

Enameled aluminum wire use Aluminum material as the core , with high heat resistance, good flexibility .

Thus greatly reduce the cost , it is easy to adhere to the fixture, also can reduce freight and production

process of operation .

2. Product Characteristic:

Products are widely used in transformer , ( air conditioner , the refrigerator , freezers , washing machine ) ,

Car motor, compressor , microwave oven , charger , ballast, relays , degaussing coil, lighting industry and so on .

3.Specification ：

Diameter Specification: 0.12mm-3.2mm

Spool size : PT4,PT10, PT15, PT25

Model: UEWAL --130℃/155℃ /180℃ , CEIWAL--200℃ ， EI/AIWA-- 200℃

4. Reference Picture:

Enameled Aluminum Wire

Q: wires have been cut and i have 4 wires i dont know what do.what colors are for what?: What are you wiring??

Q: What would the wire size be for a 3 phase 4 wire - 480/277V - 400A panelboard. Would it be (3) 600mcm w/ (1) 1/0 ground?: Well not quite: 1. The panelboard is 4 wire therefore the (3) in the description would be (4). The 4th wire is for the neutral and required if you are using the 277. Otherwise the panelboard is a 3 wire board and no 277 2. 600 kcmil copper with 75°C insulation is able to carry 420 A as long as the ambient temperature < 86°F (30°C) and are installed by themselves (not in a raceway/cable tray with other power conductors). If the conductors are aluminum, the temperature is hot, the installation has multiple conductors in the same raceway/cable tray, or the distance is of sufficient length resulting in unacceptable voltage drop, the cable must be derated -- read you must increase the size to 750 kcmil or increase the insulation rating to 90°C The ground conductor should be of sufficient size

Q: has black wires.: Two black wires in the box would be a hot from the supply and a switched hot to the load. If the timer has only two wires then it should be pretty easy to just connect them. If they are marked line and load then you would have to hook the wire for line to the wire in the box that is always hot from the supply and the other to the wire marked load. If you are still unsure then it really is not a job for you alone, enlist the help of someone with a bit more experience or even an electrician.

Q: trying to install a 7 inch dvd,cd player but do not know what all the wire colors mean , some1 has cut off the harness now all i got is a bunch of strange colored wires , it has 2 reds and many other odd color wires: I'd okorder /installbay/foru... zxc

Q: Well I have a mono D and it has - - + + on it and I want to to wire my dvc 4ohm sub to 2 ohms but I'm not sure what terminals I hook the speaker wire up to?: wire okorder /... and than wire it to any of the negatives on the amp its all one channel internally so it really doesn't matter which negative u use. than wire the positive to any positive on the amp.

Q: What Spark Plugs and Wires would optimize my MPG? 2000 Bonneville SSEI: AC Delco plugs wires. Using substandard low end aftermarket cheap junk doesnt help your vehicle at all also replacing spark plugs wires really doesnt improve your MPG unless its misfiring badly

Q: What is the wiring for one headlight on a fourwheeler that has high and low beams.: one terminal on the bulb is common to both low and high beam. that will be the ground. the other two are the hi and low beam supply .take a test light and see which two of the three wires has power to ground . once the two hot wires are identified , the third wire will go to the common terminal on the head light bulb. take the other two and see which is hi and low by switching the switch and connect to the bulb . test the light before reinstalling it if there is no power at the wires than the problem is somewhere else

Q: I did an engine swap with some friends and everything is in place, from the rebuild 700R4 w/ a shift kit, to the rebuild 350 bored .30 over. But all I have left to do is the wiring, but have no idea how to. So about how much would it cost to have a professional finish the wiring?: Wait a sec. You recommend if Congress provides the administrative large potential to inspect on individuals, it will use it? Benghazi is a witch hunt being devised from a tragedy. it particularly is Republicans searching for political hazard. The AP surveillance is a hundred% criminal because of the fact congress exceeded a regulation announcing it particularly is under our final president. The IRS difficulty, is a localized adventure in Cincinnati, which got here approximately and became got here upon final 12 months. The operative became released. The president had not something to do with any of this. i discover the AP tale aggravating, besides the shown fact that it particularly is totally criminal. i discover the IRS difficulty troubling, besides the shown fact that it became dealt with some distance faraway from presidential notice. relax. i'm effective you will locate yet another marvelous merchandise to distract you quickly.

Q: One hundred meters of a certain type of wire has a resistance of 7.2 Ω. What is the resistance of 2.5 m of this wire?I figured it would just be a proportion so (7.2 * 2.5) / 100 = 0.18 Ω. Is this the correct approach?: Ya!u r correct. L1=100m R1=7.2ohm.New length,(l2)=2.5m R2=7.2*2.5/100 R2=0.18ohm

Q: What happens when you hook these 2 wires up right along each other?: if you have an rca tv which works with 12 volts.......if the wires not connected to battery...there no problem. if connected to battery....the fuse blows.(close to battery on wire)....if there is no fuse....wires burn...risk of fire....do not forget...every device works with car battery MUST and MUST be eouipped fuse .

Send your message to us

*Email

*TEL

*Quantity

*Unit