Enameled Copper Clad Aluminum Wire
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Product Description
Enameled CCA wire is a new magnet wire with CCA Core, it combines the good copper conductivity and aluminum light weight . So that can greatly reduce the cost of winding wire, ECCA wire with the copper layer is not easy to oxidation and easy to welding. Our company has more than 100 sets of high-speed drawing machines, annealing stoves with vacuum tube and enameled machines . we also have the solderability test instrument , automatic spring back angle test instrument and dielectric loss test instruments to ensure the quality in each step. The output of ECCA wire is 500Tons per month .
2.Product Characteristic
1.the high-frequency transformer& normal transformer
2. the inductor, the electromagnetic coil
3 For the higher environmental requirements using motor : including household motor, all kinds of micro-motors, and compressors
4. the special magnet wire for audio coil & drive
5. magnet wire for the display deflection coil
6. magnet wire for the degaussing coil
3.Specification :
Dia: 0.06mm-2.5mm
Normal Package : Spool Size : PT4,PT10,PT15,PT25
4.Reference Picture
- Q: how do i tap a speaker wire? car audio not really my department
- RE: Why Monster XP speaker cord sounds worse than production facility speaker cord? purely put in Monster XP speaker cord to all my Onkyo audio gadget and now its lots softer than the speaker cord that got here with my Onkyo receiver. quantity was once at 25-35 and it grew to become into loud and sparkling. Now after the Monster XP cord, I would desire to crank the receiver to approximately 50-60 to get the comparable sound...
- Q: I have a 5 pin ignition. I have Black and red wire coming from behind the starter.Yellow wire on the other side of the engine that is connected to the magnet by the fly wheel.Where do I put these wires in the ignition switch. ____ ____ __
- You need to hook three wires into a five terminal switch? You aren't helping us much with any usable information. The yellow wire is the kill wire from the magneto. The black and red wires are hot from the battery and feed to the starter solenoid, assuming the switch has a start position. You need to check each terminal on the switch with an ohm meter to determine which function it serves and test the black and red wires with a volt meter to determine which one is hot now. Better still, why don't you specify the make and model, even the serial number if you can get it, and ask if anyone, including your local dealer, has a wiring diagram for that particular machine.
- Q: I had my uncle-in-law hook up my American Bass Pro 800 Watt Amp but he used cheap wiring. The wire is fairly small and he told me it doesnt matter how big the wire is. But what i wanna know is, Is the wire giving the amp enough power or does American Bass Pro Amps suck?? Help please
- your uncle obviously doesn't know what he's talking about. You can tell him I said that. If you want to get a lot of water to your garden, you use a bigger hose. If you want to get a lot of power to your amp, you use a bigger wire.
- Q: I need the wiring diagram for the factory radio of a 2008 ford explorer. i need to know which wires are for the back speakers so i can connect my Hi-Lo converter to it!? thanks
- I believe this is what you are looking for, or should help... 2008 Ford Explorer Car Stereo Installation Instructions Car Radio Battery Constant 12v+ Wire: Blue/Red Car Radio Accessory Switched 12v+ Wire: Green/White Car Radio Ground Wire: Black/Blue Car Radio Illumination Wire: N/A Car Stereo Dimmer Wire: N/A Car Stereo Antenna Trigger Wire: N/A Car Stereo Amp Trigger Wire: Violet/Red Car Stereo Amplifier Location: N/A Car Audio Front Speakers Size: N/A Car Audio Front Speakers Location: N/A Left Front Speaker Positive Wire (+): White Left Front Speaker Negative Wire (-): White/Brown Right Front Speaker Positive Wire (+): White/Violet Right Front Speaker Negative Wire (-): White/Orange Car Audio Rear Speakers Size: N/A Car Audio Rear Speakers Location: N/A Left Rear Speaker Positive Wire (+): Brown/Green Left Rear Speaker Negative Wire (-): Brown/Yellow Right Rear Speaker Positive Wire (+): Brown/White Right Rear Speaker Negative Wire (-): Brown/Blue
- Q: i bought a wiring kit off OKorder it was a bullz 4 gauge kit. and i am running a rockford 500.2 n its rated for 700+ watts. so do you think my cheaper wiring kit is affecting performance? should i go snag up some bigger power wire for more power to run through it or is tht not how it wokrs?
- you should add a capacitor to your system. a 5 fared should be good. it is a reserve for when the bass hits. it's less stress on your alternator and battery. and you won't get the headlight dimming affect when you have it cranked up. ask your local car audio shop. you should be good with 4 gauge.
- Q: I am replacing old 3 button (vertically aligned) light switch. There is 1 thick wire wrapped in white, 1 thick wire wrapped in black and 4 thin wires wrapped in black. I attached the white wire to the common wire screw and put the remaining wires around the screws. I am also replacing a toggle switch that will control the vanity lights above the sink. There are 4 clumps of wire coming through the box. The copper grounds are all twisted together, and there are multiple strands of white covered wire twisted together and then the 5 black cover wires and 1 white covered wires. After hooking it all up, it doesn't do anything. No lights, fan or heat lamp. What did I do wrong?
- Jeff Verde nailed it but forgot one thing. Never assume that the last person that installed wiring hooked it up to the right colors! I've even seen people use a hot wire (Black) as the ground. Never assume it's right to start with!
- Q: can anyone please tell me what does hook-up wire mean and how does it differ from other kinds of wires such as light duty and heavy duty?Also,which one should I use for breadboards?
- Hookup wire is a term usually reserved for wire sizes smaller than 16 AWG, usually single strand conductor. It is generally used in applications where current-carrying capacity is not of prime importance. Breadboarding is one of these applications, but usually uses 22AWG or smaller wire.
- Q: How can it be possible to create a high voltage and have a small gauge wire? Example: 3gj or 3000mw in a small wire (just an example)
- Voltage don't matter. It's the amps that will kill the wire. Just have really high voltage and low current and you can have lots of power going through smaller gauge wires. That's how it's done with overhead power lines.
- Q: We are replacing an older style submersible 3 wire well pump with a newer style 3 wire plus ground. I do not know where to ground the green wire? Is it necessary to extend the wire from the pump all the way to the top and ground it there or can i just ground it to the pump itself? Any ideas? First time home owner... trying to save money and not call an electrician (Im an avionics technician so I have some what of an idea what im doing.) Thanks
- All wires coming from the pump should terminated in the Pressure Switch box. Take the green wire from the pump and the ground wire from the house, connect them together with a pigtail wire and attach the pigtail wire to the ground screw within the Pressure Switch box.
- Q: I have seen 2 wire detectors and horn strobes, and 4 wire detectors and horn strobes. What is the difference? The 2 wires are cheaper.
- In 2-wire systems the power and the detector signal are multiplexed onto 2 wires. The detector has to have circuitry to extract the power and multiplex the signal onto the wires, making them slightly more complex. In 4-wire systems the power is separate from the signal, unless there is more than one signal from the detector (i.e. smoke heat). It could be 2 wires for power and 2 wires for a single signal (i.e. smoke), or 1 wire for power, 1 wire for smoke, and 1 wire for heat, with the 4th wire being common to all 3. .
Send your message to us
Enameled Copper Clad Aluminum Wire
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords