Car Lift3T/4T/5T And Two Post,Four Post Lift Manufactory
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1000 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Main Features
1. Double hydraulic cylinder drive, stable lifting.
2. Mechanical safety latch in two carriage's back.
3. Automatic stop in the highest position.
4. Linear cut chainwheel arm locking device.
5. Synchronization cable and high intensity chain.
6. 24V low-voltage safe control keeps the users away from unexpected injury.
7. Relief valve protect against overloading.
8. Press “UP” button on motor for lifting.
Specification
Item No. CMTL3.5B
Lifting capacity 3500kg
Lifting height 1860mm
Minimum height 110mm
Overall height 2750mm
Overall width 3320mm
Length of long arm 820-1280mm
Length of short arm 710-1050mm
Width between columns 2760mm
Lifting time ≤60s
Lowering time >30s
Motor 220V/380V 50Hz/60Hz 1Ph/3Ph
FAQ
1. Why should I choose CNBM 2 post car lift?
There are several reasons you should strongly consider purchasing a CNBM Lift:
Top raw materials from only the finest plants
Only professional cost-effective equipment
Low prices with high quality revenue producing products
Increase productivity for your customers( Your customers gain more, they will enjoy buying from you.)
The best customer service. Quick reply within 24 hours and more.
Great Warranty
2. How safe are your 2 post car lift?
Our 2&4 post lifts have been tested and CE certified for safety . They also meet the American
and Australian Standard.
3. Should I keep repair and replacement parts in stock?
Yes, most all commonly required repair and replacement parts should always keep in stock.
4. What type of fluid is required for my 2 post car lift?
We recommend use of a SAE10 hydraulic fluid that meets an ISO 32 specification, approximately 3 gallons / 12L are required.
5. Are CNBM 2 post car lift designed for commercial use?
All of our lifts can be used in commercial applications without any problems.
- Q: A hydraulic machine that can raise a car weighing 50,000 N and rests on a piston with a cross-sectional area of 2m^2, what force must be applied to the smaller piston that has an area of 0.5m2, in order to lift the car? I don‘t understand how to do this problem, please explain.
- Do you have the nut off were the arm is on the splines?It is splined and hard to get them off,you may need to pry it off as they are tight to the splines.
- Q: I bought an Audi a while back. I‘ve been pulled over three times for the same reason. There is a warrant issued to the car. I would like to know how i can get this warrant lifted?
- This is not to solve your problem. just an FYI (find the fix for your problem before trying these). for all. the new dynamic balancing beads are great if you have a parts store that carries them just let the air out and pour 'em in thru the stem. Check 'em out.
- Q: A stuntman drives a car (without negative lift) over the top of a hill, the cross section of which can be approximated by a circle of radius R 227 m. What is the greatest speed at which he can drive without the car leaving the road at the top of the hill?
- I am a heretic. Purists say there is no such thing as centrifugal force. There is, you just introduce a Rotating Frame of Reference. Because: A rotating reference frame can have advantages over an inertial reference frame.[15][4] Sometimes the calculations are simpler (an example is inertial circles), and sometimes the intuitive picture coincides more closely with the rotational frame (an example is sedimentation in a centrifuge). By treating the extra acceleration terms due to the rotation of the frame as if they were forces, subtracting them from the physical forces, it's possible to treat the second time derivative of position (relative to the rotating frame) as if it was the absolute acceleration. Thus the analysis using Newton's law can proceed as if the reference frame was inertial, provided the fictitious force terms are included in the sum of forces. For example, centrifugal force is used in the FAA pilot's manual in describing turns.[16] Other examples are such systems as planets, centrifuges, carousels, turning cars, spinning buckets, and rotating space stations. So draw the picture. Centrifugal Force up Gravity down Fdown M*9.8 m/s^2 Force up M *(v^2/r) M*9.8 M*(V^2/r) Cancel the M 9.8 V^2/227 GO
- Q: 2002 Nissan Sentra SE-R Spec v, 83k on engin 130k on car.The repair manual says that it could be the crank and rod bearings. but that doesnt fit in my mind with the sound.on start up, about 50-60% of the time a loud almost rattle , it follows the pitch and tone of the engine but after start up only low gears barely and rarely will i hear the faint sound of it imo i think its a loose heat sheild or something, im going to get my oil change here soon too so idk but i havent really investigated to much , just want some opinions first. thanks in advance
- Have it put on a car lift and check the complete exhaust system front to back.
- Q: When I have my foot on the brake at a complete stop, my car sometime shakes more than usual. Pepboys said this is from the engine mount and reccomended I replace it. Would a bad engine mount cause this. I just had new front brakes, front rotors, and rear drums installed. I drive a 99 cavalier
- Games 'n eCards – Elephant Rogers Student – Home Rogers Student II – Automatically Trivia Thread for September 4th – autelebchom
- Q: Does being able to carry or lift up someone mean you have great physical strength??
- Depends how much they weigh .
- Q: also, I like to watch videos of jeeps off roading. What exactly is happening when the vehicle itself stays level, but the wheels are crooked?
- A Suspension lift is usually a kit that has longer springs that puts the body/frame further away from the axles. Which is preferred over a body lift which only seperates the body from the frame. A suspension lift also provides more suspension travel. Which leads me to your next question. What you see those Jeeps doing when the tires move but the body stays fairly level is called flexing or articulation. All suspensions provide this movement but it depends on the suspension design as to how much flex it has.
Send your message to us
Car Lift3T/4T/5T And Two Post,Four Post Lift Manufactory
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1000 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
