0.6/1kV PVC Insulation Power Cablessssssss
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 10000 m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Application
This product is apply to AC rated voltage 0.6/1kV circuit, for the use of power transmission and distribution.
2、Type and Specification
Voltage Class | 0.6/1 kV |
Type | VV 、VLV、VY、VLY、VV32、VLV32、VV42、VLV42、VV62、VLV62、VV72、VLV72 |
Size Range(mm2) | 1、2、3、4、5、3+1、3+2、4+1 cores:1.5~400 |
Executive Standard | GB/T 12706.1-2008 |
3. Operational Performance
a. Cable conductor allowed long-term working temperature not exceeding 70 ℃.
When short circuit happened (the duration no longer than 5 seconds), the maximum temperature of cable conductor is not exceeding 160℃.
b. When laying cable, the ambient temperature should not be lower than 0℃,if not the cable need to be preheated. The bending radius of multicore unarmored cable should not be less than 12 times of outer diameter of cable, 15 times for armored cable.
c. Cable DC resistance should comply with GB/T3956-1997.
d. Power frequency voltage withstanding test: 2.5 U0 +2kV/5min no breakdown.
4、Cable structure diagram
1-Conductor 2-Insulation 3-Tapedcovering 4-Filling
5-Inner sheath 6-Armour 7-Outer sheath
- Q: i have a lightning audio amp, it was wokring a few months ago when i pulled it out of my car, i tried yesterday to see if it worked, it turned one for 5 seconds and went into protection mode, so i tested it with the battery and it did the same, and the cables got hot, and help please
- Having the alarm put in should not affect your amp, I hate taking my car somewhere thinking someone might play with, and maybe break my toys. But yes they were right always sand the ground spot till its nice and shiny but I cant see a week ground tripping the protection light. Try unhooking the power wire and run a temperary one from the amp to the battery to see if your power wire might be the culprit by wearing and posibly lightly shorting against metal. The power wire is the most likely to be the guilty party if everything bench tested good (also relace the fuse at the battery they can become defective without breaking I had that happen before) Good luck.
- Q: Seem to have misplaced both the power cable and adaptor for my hp printer scanner all in one and every where i look i cant seem to pick them up can any1 help me ?
- Start with the model number of the scanner and find a power supply. Carl
- Q: I need 600W of power for my new computer, but all I have is 2 300W, 20-pin power supplies. What I'm wondering is if I can combine the 2 20-pin connectors and turn them into 1 24-pin connector?
- relies upon on the producer are you advantageous its basically 20 pin as some 4 pin connectors grasp freely so how many different 4 clusters do you have you will desire to have 2 one million of those would be the different connector you go with except its an exceptionally very very old cheappy PSU inwhich case replace it they ordinary and much less costly 30 bux
- Q: Power cable yjv22-10kv-3 * 50 what it means
- Yj is cross-linked polyethylene insulation, v PVC sheathed 22 is double steel tape armored, voltage 10KV, 50 square three-core copper cable
- Q: Is the power cable considered a fixed asset?
- According to the total number of meters, such as where to where a total of how many kilometers (meters). Power system fixed assets asset management software - TU Teng fixed asset management software.
- Q: i have an amp with an 80a fuse i figure i shoud use a power cable with a 100a inline fuse what guagee should i use? also can i get two 8 guage wires with 50a inline fuses both to the ampthanks guys
- always go with the 4 gauge...u dont need to go any bigger like 2 or 0 gauge unless u just want to....alot of people say to go 2 gauge or 0 gauge when u add more power but look at ur powerline to ur house...its 4 guage and it generates 10x the current ur car will.....
- Q: what is the easiest way to replace the power window cables on the motor in the passenger side of a '94 accord
- If you are referring to the electrical wires leading to the power window system, then you need to cut wires and splice new ones back into the system along with the plug at the end of the cable.
- Q: today i purchased a used audiobahn atb10at 10quot;subwoofer with a built in power and for my car but there was no cables for it, the power is a six prong plug and i was wondering if anyone could tell me what the specific name of this cable is or where i can buy it and maybe how to install it, i tried looking into it and didnt get anywhere thanks
- That's actually a six prong molex connector commonly used in computers. You might be able to get the male end from a computer shop or maybe a place like Fry's or CompUSA. I found a website that has them too and included the link below. For how to wire it up, it's actually printed on the box right next to the connector. The top three wires are as follows: Top left = 12v+ Top middle = remote Top right = ground The bottom three aren't even used in this setup. Also, the factory specs say, you need to use 12 gauge wire for the power and ground and 18 gauge remote wire. Enjoy!
- Q: I cant find the power cable for this CRT monitor I have, But I have this power cable from an LCD monitor. Would it work if I put the LCD monitor power cable in the CRT monitor? Will it fry the CRT if I try?
- I've used the same power cables for about 10+ years. Whether CRT, LCD, external disk drive, etc. It should be fine.
- Q: I need to replace the power cable for my HF M300, but I'm having trouble finding the proper one. Can somebody tell me what it is I need (preferrably at OKorder)?Thanks!
- The power adapter that came in the box is Canon's CA-570. Search for that at OKorder.
Send your message to us
0.6/1kV PVC Insulation Power Cablessssssss
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 10000 m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches