QDX.QX Series Stainless Steel Submersible Pumps

Ref Price:

Loading Port:: China Main Port

Payment Terms:: TT OR LC

Min Order Qty:: -

Supply Capability:: -

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

AY series oil pump

SK-3A water ring vacuum pump

Self priming 8 inch Centrifugal sewage electric motor pump

Refrigeration Oil Vacuum Pump

QY Oil-filled Submersible Pump

Clean Water Centrifugal Water Pump for High Flow Rate

Chemical Process Pumps with IH Series for High Temperature

High Pressure Booster Pumps for Water Supply System

Product introduction:
QDX. QX series submersible pump consists of pump, mechanical seal and motor. Pump is at the bottom part of pump, which is adopted centrifugal impeller.Motor which is monophase or three phase is at the upper pa" of pump and seal is used where pump and motor combine, which is a kind of double end mechanical seal "O " rings are applied to all static joints. Floator switch can be equipped to control pump" starting and stopping automatically according to the water level.

Application:
This series pump is small and light, which is widely used in countryside for elevating water from well, irrigation, sprinkling and domestic water supply, and also used in draining off water for fishpond and building site.

Work Conditions:
The pump can work properly and continuouslyunder following operational conditions:
1 .Medium is not corrosive, Sand contents shouldbe max. 0.10% by volume and granular sizeshould be max.0.2mm.
2.Medium temperature shouldn’t be over 40℃ and PH should be6.5-8.5.
3.The pumps should be operated within rated head.
4.The pumps should be fully submerged into water with depth of less than 3m mad max. the pump should be min.0.5m over the water bottom and not be inserted into sludge.
5.Power frequency should be 50Hz, single phase voltage 220V, three-phase voltage 380V, and voltage fluctuation should be 0.9-1.1 times than the rated .

Q: What are the meanings of the vacuum pump, the front pump and the main pump?: In operation, the main gas extraction limit vacuum is achieved by the main pump, so we call it the main pump, which plays the main role of the pumpThe front pump is the pump that needs to be opened ahead of the main pump. It is called the pump before the main pump and the pump running the main pumpIf you don't understand, look at your signature and ask again

Q: Is the diaphragm pump and the drain pump one?: First of all, there's something wrong with your concept.Diaphragm pump is in accordance with the way the pump classification, drain pump is in accordance with the use of pumps classification.

Q: What are the reasons for sealing damage of centrifugal pumps?: Two, cavitation. Cavitation (mainly from a thermal centrifugal pump).Because the medium is hot water, the water temperature is too high to produce steam, the gas in the pipeline enters the pump cavity height, and the part of the gas can not be discharged, thus causing water shortage to run, the machine seal dry grinding is invalid, and the cavitation erosion device is not available.Process: replace the machine seal.

Q: Double floor sewage pump circuit diagram of a small problem: Q 2, SA and SS are select switches, and different positions indicate the same difference between the two nodes. SA hits the left position 13, 14 to connect, hits to the right position 21, 22 to connect. SS hit the middle position, 5 and 6 turn on, 7 and 8 turn on; hit the right position; 1 and 2 turn on; 11 and 12 turn on; hit the left seat; 9 and 10 turn on; 3, 4 turn on.

Q: What does "efficiency" mean in a water pump catalog?: General pump efficiency is 60% ~ 85%. high efficiency of the pump, indicating the same work, the pump consumes the lowest energy, and vice versa

Q: Direct connection pump What is straight pump and non direct pump? What's the difference in structure?: What is straight pump and non direct pump? Direct coupled pump shaft and the motor shaft is directly coupled with the coupling and non direct coupled pump: pump shaft and motor shaft through the belt pulley, V-belt connection or other forms of transmission. What is the difference in the structure: the direct coupled pump has the advantages of compact structure, simple installation, but the relatively small power; non direct coupled pump: pump and motor is independent, the two transfer torque through the belt, the structure is relatively large, complex installation, general power is relatively large.

Q: Is vane pump good or gear pump good?: 1) the reversible design of gear pumps can also usually reverse, but reverse after the suction port change, and the pump safety valve does not work; leaf pump is generally not allowed to reverse. 3) the single acting vane pump can be designed to change the eccentric distance by moving the stator at the constant speed, so as to achieve the purpose of variable direction.

Q: What is the cause of the damage of pump bearings?: In high-speed equipment, the most likely damage to bearings is high temperature.

Q: How to maintain and repair the booster pump of pipeline pump?: 4. install "0" ring, tighten the pump body and motor end cover with bolts. Notice that the clearance between the front cover of the impeller and the pump body is 20. 0.5 mm. The impeller inlet, the outer ring and the pump body ensure a certain running clearance.5. the disassembly order is the opposite.

Q: What is the series of pumps? What is the difference between a unipolar and a multilevel? What is the meaning of each "first class"?: Each impeller is of the first stage. (two impellers share only one level, and exit is only level one)

Send your message to us

*Email

*TEL

*Quantity

*Unit