High Quality Galvanized Iron Wires For Chainlink Fencing

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Galvanized Wire/Galvanized Steel Wire/ Gavanized Iron Wire

Diatmeters:0.15mm-6mm

Application	Weaving, braiding, fencing, cable armoring, knitting, tie wire, for redrawn, for binding or forming etc.
Material	low carbon steel wire
Diameter	0.15mm~6.00mm
Tensile strength	350-500MPA, or higher
Zinc coating	Min 12g/m2, min 25g/m2, min 200g/m2,min 300g/m2,610g/m2
Surface treatment	Hot dipped or electro galvanized
Packing	On spools In small coils of 25-50kg/coil, 10kg/coil In rosette coil of 100-800kg/coil
Standard	ASTM 641, EN10257-1& EN10244-2

All can be produced according to customers’ requirements.

Q: Wiring: when connecting a wire dryer outlet to 10/2 with ground romex, where does the white/black and ground connect to on the outlet?

Q: A 0.500 g wire is stretched between two points 95.0 cm apart. If the tension in the wire is 600 N, find the wire's first, second, and third harmonics.______Hz (1st)______Hz (2nd)______Hz (3rd): Kia ora In order to answer this question, we first need to ascertain the speed of a wave in this wire. The speed of a wave on a wire depends upon the tension 'T' and the linear density (mass per unit length) 'μ' of the wire. v=√(T/μ) T=600 N The linear density of your wire is 5.00E-4 kg/0.95=5.263E-4 kg/m. So for this wire, v=√(600/5.263E-4) =1068 m/s Now we have the speed, we need to find the wavelengths that correspond to the harmonics we are interested in. The wire is fixed at both ends. Nodes occur at fixed ends. Therefore the first harmonic will occur when there is a node at each end and the longest possible wavelength that satisfies this condition is λ=2L (you get half a wavelength on the wire). So λ=2*0.95=λ=1.90m. If v=1068m/s and λ=1.90 then by the wave equation v=fλ f=v/λ=1068/1.90=562.1 Hz. So that is the first harmonic. The second harmonic has twice the frequency of the first; the third harmonic has three times the frequency of the first. The second harmonic will therefore occur at 562.1*2=1124 Hz and the third at 562.1*3=1686 Hz. Because your data was given to 3sf you need to round your answer to 3sf: 1st harmonic: 562 Hz 2nd harmonic: 1120 Hz 3rd harmonic: 1680 Hz

Q: Im replacing the factory rear speakers in my car but cant figure on which wires are positive and which are negative. I went on a site for impalas but the color wires they have listed are not the same color wires in my car your help will be appreciated.: Left Rear Speaker Positive Wire (+): Brown Left Rear Speaker Negative Wire (-): Yellow Right Rear Speaker Positive Wire (+): Dark Blue Right Rear Speaker Negative Wire (-): Light Blue

Q: Having some trouble wiring fixture it seems to just stay on with the switch doing nothing.. here's the deal I have three different wires coming from ceiling power in, power out, and I believe switch.. there was a priovious light there so I know its correct just don't what wires go with what all help will be appreciated thanks: tricky subject. check out from bing and yahoo. this can assist!

Q: Just moved into a new house and the basement is already wired for surround sound. The ends are two wires one silver one gold/brass wrapped together with plastic. Looks like they were cut at the ends. How difficult would it be to wore the speakers myself?: The color coded wire will correspond to the connection of the positive and negative. You would connect the wire to the receiver, depending on the location of the speaker. Check the speaker that is already installed and see what color wire is going to what terminal on the speaker and match that connection to your receiver. Front speaker connected to the front speaker terminal of the receiver. Your receiver owners manual will also provide you with some direction. Hope this will help you out.

Q: The wire in my headphones broke right next to the jack plug. I had a pair of crappy earphones that I have cut up as a replacement jack plug but no matter what I do I cant get any response. Is it because headphone wires are not compatible with earphone wires?Thank you: Copper wire is copper wire.The headphones have other issues, or you're not connecting the wires properly.

Q: In a telephone splice case, do you have to strip the 2 wires you want to splice, and put them together, or does each wire that you want to connect attach to terminals in the case? I am talking about the black cases on a utility pole, that the residential phone wiring connects to.: In okorder .... (but not that big), then no, the wires do not need be stripped, just forced between the tines, the process of which nicks the insulation so the wire is in contact with the terminal. A pro uses a punchdown tool, but you can simulate the effect with a finger on one side and some needle nose pliers on the other. Be sure to seat it well to the back, and don't put more than one wire in a clip. The horizontal rows of 3 or 4 tines are connected together.

Q: Why would I want to upgrade the wires on my airsoft gun? What does it do?: I think it prevents the wires from overheating and melting the insulation which could lead to a short.

Q: I need to get some wire to hook my capacitor to my amp and every wire I see says that it's power/ground cable wire. Does this mean it's power wire? Or ground wire? Or does it mean you can use it for both?: you can use it for both same stuff

Q: Why is thin strand wire better for powering car audio?: Thin strand wire is more flexible and so stands up to the flexing and vibration in a car application better. May not be an issue in the short term, but over time the thinner strand should hold up better

Send your message to us

*Email

*TEL

*Quantity

*Unit