Galvanized Steel Wire For Fence

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Commercial Galvanised Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

(7) Zinc Coating

Meet GB/T 15393 standard.

Q: i need to know how to rewire it to make it fire the only wire that is still there is the one that runs to the distributor cap all the other wires are gone is it sopose to wire to the key please help: to the + terminal of the coil, run a wire that sends 12v. when the ignition switch is turned on.

Q: I need the wiring diagram for the factory radio of a 2008 ford explorer. i need to know which wires are for the back speakers so i can connect my Hi-Lo converter to it!? thanks: I believe this is what you are looking for, or should help... 2008 Ford Explorer Car Stereo Installation Instructions Car Radio Battery Constant 12v+ Wire: Blue/Red Car Radio Accessory Switched 12v+ Wire: Green/White Car Radio Ground Wire: Black/Blue Car Radio Illumination Wire: N/A Car Stereo Dimmer Wire: N/A Car Stereo Antenna Trigger Wire: N/A Car Stereo Amp Trigger Wire: Violet/Red Car Stereo Amplifier Location: N/A Car Audio Front Speakers Size: N/A Car Audio Front Speakers Location: N/A Left Front Speaker Positive Wire (+): White Left Front Speaker Negative Wire (-): White/Brown Right Front Speaker Positive Wire (+): White/Violet Right Front Speaker Negative Wire (-): White/Orange Car Audio Rear Speakers Size: N/A Car Audio Rear Speakers Location: N/A Left Rear Speaker Positive Wire (+): Brown/Green Left Rear Speaker Negative Wire (-): Brown/Yellow Right Rear Speaker Positive Wire (+): Brown/White Right Rear Speaker Negative Wire (-): Brown/Blue

Q: how do i wire a dual 2 ohm sub to an amp at 2 ohm: actually tc your almost right. yes 1 and 4 are the ohm loads of the speaker itself. but if your talking mono thats all you can achieve. on 2 channel amps when you bridge them your talking ohm drop again. so if you have one dvc 2 ohm wired in series and then bridged to the amp your looking at a 2 ohm load

Q: A wire has a resistance of 21.0 ohms. It is melted down, and from the same volume of metal a new wire is made that is three times longer than the original wire. What is the resistance of the new wire?: The resistance of the new wire is (in terms of its length, area resistivity); R2 = pL2/A2 And the resistance of the original wire is; R1 = pL1/A1 The ratio is;(resistivity will cancel because its the same for both situations) R2/R1 = L2A1/L1A2 given L2 = 3L1 R2/R1 = 3A1/A2 To find the new cross-sectional area ,require the volumes to be equal; L2A2 = L1A1 3L1A2 = L1A1 A2 = (1/3)A1 Sub this into the R2/R1 equation to get; R2/R1 = 9 R2 = 9R1 = (9)(21) = 189 ohms

Q: Kind of a confusing question I guess. I want to cut a wire that contains 3 other wires and splice into them then reconnect them. is all I need relatively the same gauge wire or is it potentially different type like some sort of special speaker wire..? Should be one positive one negative and the other some sort of signal for sound. (Microphone to a speaker). All I need is standard copper wire?: i wont even begin to touch on this,leave it alone and call a pro

Q: To help clean things up and make wiring a little more simpler on my jeep i got a fuse/relay box off an old junk car. i want to wire my off road lights into this relay box but i'm not sure what size wire is in the box it appears to be either 18 or 16 AWG one place said to strip the wire and measure the wire another says measure in the insulation. i'm not sure what to do. but if it is 18 awg would it hurt to go to a bigger size after the fuse box to my lights or should i rewire the whole box?: For okorder /... Wiring gauge always specifies the diameter of the WIRING not the insulation, since the insulation thickness can vary. You would have to strip the wire and measure the bare wire with a gauge. You can also look at the printing on the insulation for the gauge. Look for something like AWG 14 etc. You can buy a standalone headlight harness that contains the relay and wiring for aftermarket lights. I would recommend running both positive and negative wires all the way to the battery for maximum current.

Q: I have two ceiling lights in my kitchen that come into the same wiring box (light switch). It's a single light switch that controls both lights. I want to install a two fixture light switch so that I can turn on each light by itself. It looks like there are only two wires coming into the box...a black one and a white one (and a ground wire). The two-switch I bought is requiring three wires though. How do I wire this thing?: === you are going to have to rewire the lights to have the new switch operate each fixture independently == that is how it will work ... it is the only way to do what you want done .... at the present there is one pair of wires that operate both fixtures

Q: Just took off the starter on a cavalier and forgot to label the wires. Can someone please send me a diagram of where all these wires go, or just tell me where they go. there are big post and one small one. Please help asap. Thanks.: all wiring with large eyelet end,s go to main solenoid terminal...the large brass/copper post in the center/top. the small wire/wire,s attach to the terminal marked with a S for solenoid. the small terminal to the side. do not place any ground wire,s to either terminal....best of luck.

Q: thin wire to make fishing tackle that sharks cannot bite: Buy in store. Help if know what talking about.

Q: i have old wiring for a stove that iam putting in ,a new box but i have only 3 wires 2 of them are white and 1 black how should i connect on a 4 wire receptacle? on the receptacle 1 white 1 green, 4 a ground then it says x then y ???????: dont even attempt to wire it up. call an appliance service and they can test the wires for current and properly wire it up.

Send your message to us

*Email

*TEL

*Quantity

*Unit