Plastic Injection Molding Machine with Variable Pump
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 Set set
- Supply Capability:
- 3500 Sets per Year set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Detailed Product Description of Plastic Injecation Moulding Machine HXW688 Variable Pump
Clamp force:688 ton
Shot weight 2091 to 2895 gram
Oil temperature of system is reduced largely
Main specification of HXW688 |
Screw A |
Screw B |
Screw C |
Screw D | |
Injection Unit | |||||
Screw Diameter |
mm |
85 |
90 |
95 |
100 |
Screw L/D Ratio |
L/D |
22.2 |
21 |
19.9 |
18.9 |
Shot Volume (theoretical) |
CM³ |
2298 |
2576 |
2870 |
3181 |
Injection Weight (PS) |
g |
2091 |
2344 |
2611 |
2895 |
oz |
73.7 |
82.6 |
92.0 |
102.1 | |
Injection Rate |
g/s |
417 |
470 |
530 |
580 |
Plasticizing Capacity |
g/s |
60 |
75 |
85 |
100 |
Injection Pressure |
MPa |
206 |
184 |
164 |
149 |
Screw Speed |
rpm |
125 | |||
Clamping Unit | |||||
Clamp Force |
KN |
6880 | |||
Toggle Stroke |
mm |
950 | |||
Max. Mold Height |
mm |
960 | |||
Min. Mold Height |
mm |
400 | |||
Space Between Tie Bars (W×H) |
mm |
950X950 | |||
Ejector Force |
KN |
200 | |||
Ejector Stroke |
mm |
280 | |||
Ejector Numbers |
n |
17 | |||
Others | |||||
Max Pump Pressure |
MPa |
16 | |||
Pump Motor Power |
kW |
55 | |||
Heater Power |
kW |
41.5 | |||
Machine Dimension (L×W×H) |
m |
11.2×2.45×2.95 | |||
Machine Weight |
t |
39.8 | |||
Oil tank capacity |
L |
1136 |
- Q: What's the neutron in the injection machine?
- The die with an oil cylinder is mostly a core pulling action (neutron advance and retreat)Take the above product injection molding machine action is - die - high pressure lock - neutron - injection - injection - cooling - mold - neutron back - Top retreat (or none)
- Q: The working principle of injection molding machine
- The working principle of injection molding machine and injection syringe with similar, it is the use of screw (or piston) thrust, the plasticizing good molten state (i.e. viscous flow) plastic injected into the mold cavity closed good after curing stereotypesmade the process of the products.Injection molding is a cycle process, each cycle mainly include: quantitative feeding - melt plasticization - pressure, injection - filling mold cooling - die opening pieces. Take out the plastic parts and then close the die for the next cycle.Injection molding machine operation items: injection molding machine operation items, including control keyboard operation, electrical control system operation and hydraulic system operation three aspects. The injection process, feeding action, injection pressure, injection speed, ejection type, temperature monitoring, injection pressure and back pressure adjustment are carried out respectively.The molding process of the general screw injection machine is first granular or powdered plastic into the machine barrel and then through the rotation of the screw and barrel wall heating the plastic as molten state, then the machine mold and the injection seat moves forward, to close the mold gate nozzle, the pressure oil through to the injection cylinder then, the screw to move forward at a high pressure and speed will melt into the closed mold temperature low, after a certain period of time and pressure (also called pressure), cooling, the curing, can remove mold products (pressure to prevent molten material the reflux, supplementary materials, to ensure the products with the mold cavity and the density and size tolerance in a certain cavity).
- Q: What's the difference between an electric injection machine and an oil press?
- The motor has 4 servo motors, and the motor can speed up the cycle. Stability and other functions. Good motor. Anyone who has used it knows that the hydraulic press has 2 separate lines. It is the clamping circuit and the injection circuit
- Q: Quanlifa injection molding machine can replace the barrel and screw size
- Of course, the size range not too big, we do is screw barrel.
- Q: How can the injection machine be set with parameters?
- Injection molding machine, also known as injection molding machine or injection machine. It is a thermoplastic or thermosetting plastic plastic molding mold made of plastic products of all shapes of the main molding equipment. It is divided into vertical, horizontal and all electric type. The injection molding machine heats the plastic, applying high pressure to the molten plastic to make it crack and fill the mold cavity.Operation points:Before booting1. before the injection machine operation, check the electrical control box whether there is water, oil enter, if the electric equipment is wet, don't turn on the machine. The maintenance personnel should dry the electrical parts and then turn on the machine.2. before the injection machine operation, check whether the supply voltage is consistent, generally should not exceed 6%.3. check emergency stop switch, front and rear safety door switch is normal. Verify whether the motor and the pump rotate in the same direction.
- Q: What should be noticed before the machine is stopped when the injection machine is finished?
- 1, stop feeding (feed off the front barrel, the barrel bottom) has been playing in the finished material2 shut down mold cooling water before stopping,3, press the manual (if not change the mold, stop the mold to the low pressure position, protect the mold)4, mold spray rust inhibitor5, turn off the electric heat6, turn off the power7, cleaning machine sanitation
- Q: What is the best brand of injection molding machine?
- And a Hongkong Apollo injection molding machine, Kawaguchi in Shanghai foundry manufacturing, equivalent to Toshiba Shanghai manufacturing, this brand is the last time see in TOYOTA inside the car, first thought is Kawaguchi machine, before we know the results of Apollo, good mechanical recommend to you, according to their own products to choose suitable machine we canTaiwan: China machine series Qin, Huarong, Nan Rong, full of Taiwan, this machine, Fuqiangxing, etc.Japan Machine Series: Sadegh, Sumitomo, NISSEI, just, Kawaguchi, Niigata, Toshiba, MITSUBISHI...Europe and the United States series: Maffei Engel, Lubbock, Cincinnati, Albemarle, Demag, FANUC
- Q: What kind of metal material is the nozzle head of injection molding machine?
- The injection head of the injection machine is the material of No. 45 steelNozzle specifications must be confirmed: total length, diameter of tooth, distance between teeth.All kinds of nozzles, spring nozzles and split nozzles for injection molding machinesThe thread has M18*2.5,M22*2,M24*2, M24*2 lengthenedM30*2, M30*2 lengthenedM30*3, M30*3 lengthenedM36*2, M36*2 lengthened,M36*3, M36*3 lengthenedM39*2, M39*2 extended specialtyM39*3, M39*3 lengthened special skillsM42*3, lengthenM45*2And so on all kinds of specifications, various length sizes. Special specifications must be ordered ~ systemThe difference between a split nozzle and a spring nozzle
- Q: Which machine of imported injection machine is good?
- 3. Machines in Korea and Taiwan. Woo Jin, LG, Taiwan plastic, Zhenxiong Taiwan, Taichung, quanlifa, fuqiangxin, Maria, Huarong, Yi Shun exhibition, exhibition, TMC, qunji, Nan Rong, this machine, Zong Wei, Hua Qin, precision machine, plastic, plastics
- Q: Consult the injection machine and say how many grams, but I also see "360T 250T", what does this mean? Thank you
- Injection molding machine on the subject of its clamping force, the general 1T can be understood as 1 grams.
1. Manufacturer Overview
Location | Zhejiang, China (Mainland) |
Year Established | 2003 |
Annual Output Value | US$50 Million - US$100 Million |
Main Markets | North America South America Eastern Europe Southeast Asia Africa Mid East Eastern Asia Western Europe South Asia |
Company Certifications | ISO9001:2000;CE Certificate;ISO9001 Certificate |
2. Manufacturer Certificates
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability
a) Trade Capacity | |
Nearest Port | ST.PETERSBURG,AMBARLI,RIYADH |
Export Percentage | 21% - 30% |
No.of Employees in Trade Department | 3-5 People |
Language Spoken: | English, Chinese |
b) Factory Information | |
Factory Size: | 50,000-100,000 square meters |
No. of Production Lines | Above 10 |
Contract Manufacturing | OEM Service Offered |
Product Price Range |
Send your message to us
Plastic Injection Molding Machine with Variable Pump
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 Set set
- Supply Capability:
- 3500 Sets per Year set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords