Needle-punched Nonwoven Geotextile

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

made of polyester or polypropylene fiber
good burying, hydrolyzation & corrosion resistibility

Density	Thickness	Breaking Strength	Elongation of Fracture	CBR Bursting Strength	Vertical Penetration Parameter	Equivalent Aperture
g/m2	mm	KN/m	%	KN	cm/s	O95 mm
65	1.2	2.8	40 ~ 80	0.7	K x (10-1 ~ 10-3) (K = 1.0 ~ 9.9)	0.07 ~ 0.2
75	1.4	3.3		0.8
100	1.6	5.0		0.95
150	1.52	7.5		1.5
160	2.0	8.5		1.60
200	2.4	11		2.10
250	2.8	14		2.60
300	3.4	16		3.20
400	4.0	21		4.0
500	4.5	25		4.8

Q: Do you need a cushion on the ground floor?: As well as the time to build a wooden building with concrete pier, from the ground or contact the ground to do a good job preserving.

Q: Do you need a cushion for roof waterproofing?: There is no "cushion" on the roof, and there is a concrete cushion under the basement floor. What you said may be leveling, is the base of the waterproof layer.

Q: The top floor made waterproof playing cushion layer of how to do: 2. repair the cracks well. After the cracks to be repaired are dry, start waterproofing.

Q: The roof cushion is waterproof on the slope roof: and the formation of the ice dam will lead to roof water, water will find the path into the house.

Q: Is the raft cushion waterproofing full of the cushion?: Assuming (just suppose) the raft can easily turn over, then we do waterproof (like roof) directly on it, not waterproof on the cushion.

Q: Basement cushion waterproof: First, the basement moisture treatment structure is usually: first in the basement wall outer surface wiping 20mm thick 1: 2 waterproof mortar, basement walls should be used cement mortar masonry, gray seam must be full; and in the basement floor and the first Floor floor is divided into two walls of the level of moisture-proof layer. The outer wall of the basement wall should be tampered with the soil with poor permeability.

Q: Can the floor tiles be removed from the cement mats on the prefabricated board floor?: Cement cushion as a leveling layer on the floor, not designed to the structure of the load-bearing, the general can be dug, the cushion is generally 3 to 5 cm, chisel in addition to unloading the floor of the heavy objects, chisel in addition to the use of strong vibration Machine or penetrating machine is too large, with a small hammer small chisel, along the horizontal plane horizontal chisel, stripping cement cushion.

Q: Large area ground concrete cushion seam Why is the separation of joints generally concrete: hird, the relevant parts Different types of rigid waterproof layer separation spacing in addition to meet the calculation needs, but also in the following parts set sub-grid joints. 1. The deformation of the roof structure sensitive parts; 2. Roof and roof drainage direction changes; 3. The junction of the waterproofing layer and the protruding roof structure; 4. Under normal circumstances, each bay load-bearing walls should be set sub-grid seam. 5. Between the waterproof layer and the load-bearing or non-load-bearing parapet or gable should be set sub-grid joints, and in the node structure for proper treatment.

Q: What is the waterproof layer and the waterproof cushion in the tile roof?: Waterproof layer: set in the tile or metal sheet below, from the waterproof, moisture-proof structure of the layer. The waterproof cushion plays an important role in the tile surface, because the "tile" itself can not be counted as a waterproof material, only tile and waterproof cushion combination to form a waterproof fortification.

Q: Basement floor mattress dry to what degree can do coil waterproof?: Third, the membrane waterproof in the construction should first do the basement floor of the waterproof, and then the membrane along the basement floor continuous paste to the outer surface of the wall. Basement floor waterproofing first in the foundation pouring C10 concrete cushion, the thickness of about 100mm. And then paste the membrane, and then in the coil to wear 20 thick 1: 3 cement mortar, and finally pouring reinforced concrete floor. The outer surface of the wall first wip 20mm thick 1: 3 cement mortar, cold base oil, and then paste the membrane, the membrane should be stitched paste, adjacent coil lap width of not less than 100mm. The top of the coil should be higher than the maximum water level of about 500mm, the outer side of the brick wall.

Send your message to us

*Email

*TEL

*Quantity

*Unit