Hot Dip G.I. Wires

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Commercial Galvanized Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

(7) Zinc Coating

Meet GB/T 15393 standard.

Q: all my wires are cut and im trying to find the power/hot wire so that i dont fry anything....im trying to hook up a new radio: Blazer Radio

Q: Just moved into a new house and the basement is already wired for surround sound. The ends are two wires one silver one gold/brass wrapped together with plastic. Looks like they were cut at the ends. How difficult would it be to wore the speakers myself?: If the wire you are referring to is standard speaker wire, then you wire it to your speakers, at one end, and to your receiver, at the other end, the same way that you normally wire up speakers. In other words, always connect the same colour of wire to each positive connection, and the other colour to all of the negative connections.

Q: Wire runs from breakers to a wall outlet along the garage wall: Ok so the first two answers are almost correct. If the breaker is 20amp it's 12 gauge wire, if it's 15 amps it will be 14 gauge wire. The outlet is in a garage it must be a GFCI receptacle. That's a national electrical code requirement. If the wiring is to be exposed (ie not inside of a wall) then it must be in conduit, cheapest and easiest to install is pvc, you can run romex or NMB through conduit. If the wall is to be sheetrock when finished then you can run just romex through the studs. It is recommended that the GFCI receptacle be mounted in an extra deep box but is not required, makes it easier to get it in there with the wires. You can put up to 8 receptacles or devices, like light fixtures on one 20 amp circuit. More and you will be over loading the circuit. The romex you run should be for 20 amp 12-2 with ground. All circuits and devices must be grounded to be in compliance.

Q: Wire 1 and wire 2 are made from the same metal. Wire 2 has a larger diameter than wire 1. The electric field strengths E1 and E2 are equal. A) Compare the values of the two current densities. Is J1 greater than, less, or equal to J2?B) Compare the values of the currents I1 and I2. Is I1 greater then, less or equal to I2?: The current will be more dense in the smaller wire. The value of the current is inversely proportional to the resistiance of the wire. Resistance = resistivity * length / Area since the wires are of identical material and length, the only thing left to vary is the cross-sectional area. Area is proportional to the square of the radius (diameter), so the current will be proportional to the square of the diameter. I2 is proportional to I1^2 I2 is larger than I1 .

Q: Hello,I got a ventilation fan for the bathroom. The fan has 2 wires and there are 2 wires sticking out of the wall.How do I know which wire connects to which wire?What would happen if I connect the wrong wires?: Usually its a white/red and a black wire that stick out of the walls/ceelings. All you need to do is to match the colors together, red/white on red/white and black on black. White is usually the live wire and black is the return wire. If you plug them the other way around you can short out your lamp and pop your breakers or burn a fuse. just make sure the wire is not live so unclip your braker or unscrew your fuse for that circuit. If all your wires are black you will need a electric meter to know which one is which. Also sometimes black wires have a white line on them to differenciate from full black wires! hope it helps

Q: I no longer have enough 0 gauge wire would it be bad to use 0 gauge power wire to the amp and 4 gauge wire to ground the amp?: Don't do it you will get allectorcutted.

Q: How do I wire this ceiling fan? There are two house wires coming from ceiling-one white, one black. There are three wires on the fan- one white, one solid black, and one black with a white stripe. There is one light switch in the room that will be operating the fan/light (the fan has a light on it). I wired the white wire to the white wire, the black wire with the white stripe to the black wire, didn't know where to wire the solid black wire to. Now only the light part of the fan works, the fan does not work at all. Where does the solid black wire go? I need both the fan and the light to work.: Are you located in the USA? I am puzzled by one thing and that is the red wire. Usually ceiling fans have a black wire for the fan and a blue wire for the light fixture. But if you are in the US, this sounds correct and it should work just fine. Normally a 12-3 or a 14-3 wire would be used but there is not problem with what you have done. Edit: You are correct, you simply have an extra white wire. No problem at all.

Q: How do you properly wrap copper wires? We have been using electrical tape and it's melting the tape. This is in a camper, and it's in the electrical box. We're using this tape because the wires kept touching and arcing off of each other...I'm guessing :/: If the wire is not heavy enough it will heat up from the amount of current through it. If there is a short circuit somewhere, the wires will heat up regardless. It may not be rocket science, but it certainly is electrical engineering.

Q: Okay so bought 2 Kicker Comp C12-8 subs they are single voice coil, and I bought the Kicker DX300.2 amp. I would like to parallel wire thes subs to have a 4 ohm load, But I don't totally get the concept of it. Could somebody explain it, or show me a diagram, or video, or something?: Parallel: okorder /

Send your message to us

*Email

*TEL

*Quantity

*Unit