High Quality Galvanised Iron Wires

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Galvanized Wire/Galvanized Steel Wire/ Gavanized Iron Wire

Diatmeters:0.15mm-6mm

Application	Weaving, braiding, fencing, cable armoring, knitting, tie wire, for redrawn, for binding or forming etc.
Material	low carbon steel wire
Diameter	0.15mm~6.00mm
Tensile strength	350-500MPA, or higher
Zinc coating	Min 12g/m2, min 25g/m2, min 200g/m2,min 300g/m2,610g/m2
Surface treatment	Hot dipped or electro galvanized
Packing	On spools In small coils of 25-50kg/coil, 10kg/coil In rosette coil of 100-800kg/coil
Standard	ASTM 641, EN10257-1& EN10244-2

All can be produced according to customers’ requirements.

Q: I just learned how to do 3-way wiring, so that I can turn a light off from 2 different switches. My question is, how do I add another light to that mix, so that both lights come on/go off at the same time when I turn the switches on and off? (It's for a closet that has 2 lights in it that I want to come on/go off at the same time).: You have to tie the wires that go to the light together. It is called parallel.

Q: I have a grounding wire for my HIDs which I need to increase the length for. How do I do this?: The best way would be to obtain a piece of wire the same gauge(thickness),and solder the wires together,and use shrink tube to cover the connection.If you don't have access to shrink tube,use a high grade electrical tape.The reason i suggest this as the best choice,is that HIDs are high amperage ,so that is the first choice.The second ,and easier ,is again obtaining the same type wire,and use what is called a butt connector.You strip the ends of the wires,insert them into the butt connector,and crimp the connector.You can usually buy an inexpensive wire stripper-crimper electrical kit that come with connectors at a pep-boys,advance auto or some other auto discount store for under ten dollars.Make sure that the connections are tight and secure.Shrink tube is usually included in these kits,also

Q: I have a new light fixture I am trying to install. The electrical box has two sets of black and white wires coming in. Both of the black wires are connected together while the white wires from either set were used to connect the old fixture. How should I wire in the new fixture. The switch for this light has only one set of black and white wires connected to the light switch.: Do okorder /

Q: DO i TWIST THE WHITE AND RED SMALL WIRES TOGETHER UNDER THE WIRE NUTS ON AC WIRING TO THE CONDENSER?: There will be two wires in the unit. The low voltage wires (white and red) attach one to each of the wires in the control box on the unit. There will be a wiring diagram on the inside of the ac unit access panel. Shut the power off first. Also, after you hook them back up, it may still not work. It is possible that the control fuse blew on the indoor unit. For a step by step troubleshooting guide, check out my source.

Q: I need help hooking a remote wire to my jvc kd-g220.: Chances are, that the radio has a blue wire, and a blue wire with a white stripe. One will be marked for antenna, use the other for remote, or use ignition from the fuse box. Just dont forget to fuse this if you go that route.

Q: I'm splicing four pieces of 14-2 gauge copper wire to an 16 gauge electrical cord. The copper wire doesn't have any covering on it. Is it okay to connect the grounds, then attach it to my keyless lampholder? Or is something bad going to happen then?: Ground wires are typically bare. Just be sure as you put the wires and light back in the box that the ground wire is not near the connector with the black wire. The black one is the one that bites !

Q: TRUCK WIRES, quot;orange,yellow,,red,,black,,white,,brownSTEREO wires ,,Yellow,red,black how do i hook this up right ? HELP !!: Here okorder /... It's for a 70's Camaro but it's the same. Aftermarket radio: Yellow is 12 volts constant Red is 12 volts switched Black is ground hope this helps!

Q: Is it possible for a wire to arc with a nail? The u-nail that hangs the wire to a wooden support beam looks like it was hammered in too far and may have cut through the insulation around the wire. Is this a fire hazard or can I leave it as is?: Did it cut through the outside sheathing or one of the conductor sheathing? If its just the outside sheathing, remove the staple and secure the wire further away. Use electrical tape and wrap the cut...If it has penetrated one of the inside conductors, well, without seeing it its hard to tell you. The biggest concern would be if the wire ever overheated there is less 'insulation' to prevent it from burning into a neighbouring wire. Err on the side of caution. More detail would help.

Q: do i need a wiring harness or can i use wire crimps and do it w.o on a 2000 blazer 4wd if u think i need it plz tell me thanks: unless you known what each wire does get the wiring harness or you very well may destroy your head unit

Q: I want wired internet on my xbox and was wondering if you need a wired router or can u just us a modem?: a router wired or wireless is not necessary,but it's useful if you have a computer.if you only connect your console,plug your ethernet cable from your modem to your console

Send your message to us

*Email

*TEL

*Quantity

*Unit