Heavy Galvanized Wire
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Hot Dip Galvanized Steel Wire
(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .
(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .
(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.
(4) Tensile Strength Range
Size (mm) | Tensile Strength (mpa) |
0.15-1.60 | 290-550 |
0.65-1.60 | 400-550 |
1.61-6.00 | 400-1200 |
(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.
(6) Packing
Size (mm) | Coil Size | Spool Packing | Big Coil Packing | |
ID (mm) | OD (mm) | |||
0.15-0.26 | 6 inch | 1-14kg/spool |
|
|
0.27-0.60 | 8 inch | 1-100kg/spool |
|
|
0.61-1.60 | 12/14/16 inch | 1-100kg/spool | 250-400 | 400-770 |
1.61-6.00 |
| 14-500kg/spool | 450 | 800 |
508 | 840 |
(7) Zinc Coating
Meet GB/T 15393 standard.
Size (mm) | Weight of Zinc-Coating ( g/m2 ) | |||||||
A | AB | B | C | D | E | F | ||
A1 | B2 |
|
|
|
|
|
| |
≤0.25 |
|
| 30 | 20 | 18 |
|
|
|
>0.25-0.40 |
|
|
| 30 | 25 | 20 |
|
|
>0.40-0.50 |
|
|
|
| 30 | 20 |
|
|
>0.50-0.60 |
|
|
|
| 35 | 20 |
|
|
>0.60-0.80 | 120 | 110 |
|
| 40 | 20 |
|
|
>0.80-1.00 | 150 | 130 |
|
| 45 | 25 |
|
|
>1.00-1.20 | 180 | 150 |
|
| 50 | 25 |
|
|
>1.20-1.40 | 200 | 160 |
|
| 50 | 25 |
|
|
>1.40-1.60 | 220 | 180 |
|
| 50 | 35 | 30 |
|
>1.60-1.80 | 220 | 180 |
|
| 70 | 40 | 30 |
|
>1.80-2.20 | 230 | 200 |
|
| 80 | 50 | 40 |
|
>2.20-2.50 | 240 | 210 |
|
| 80 | 55 | 40 |
|
>2.50-3.00 | 250 | 230 |
|
| 90 | 70 | 45 |
|
>3.00-4.00 | 270 | 250 |
|
| 100 | 85 | 60 | 30 |
>4.00-5.20 | 290 | 270 |
|
| 110 | 95 | 70 | 40 |
>5.20-6.00 | 290 | 270 | 245 |
| 110 | 100 | 80 | 50 |
- Q:Im wiring my pioneer deh x3600ui to my pontiac grand am gt 2002 directly without a factory harness. Any diagrams out there i can use? The red wire on my pioneer is for the ignition but i cant find that wire on the pontiac.
- if u cant find a diagram u can always check the speakers for the colors of the wires and then just try to get a hold a cheap little voltage meter like the one below just to find ur ground, remote, and battery wire.
- Q:Where would I get a 2001 wiring diagram for a Silverado chevy truck? I want to re-install the factory stereo that was taken out when I first got it? I have no idea what wire goes where. Thanks a lot.
- 01 Chevy Silverado
- Q:Im wondering if this 24 awg wire is good for guitar wiring. Doesn't look like something that i usually would see people use when wiring, since there is lots of different wires and colour coding wrapped up inside it.
- Given okorder / I hope this will help with your decision. Good luck!
- Q:I recently re-wired my house with 4 wire telephone wire. They all meet in the attic. How do I wire them together and is there some kind of junction plate I can use? Additionally, I did also wire my house with Cat6 wire, but would like to keep it strictly for Internet.
- (links just for reference, from search engine results)
- Q:Will you please remove any of the wires? The edge of the body, which is made of wire or what? Is it copper or iron?
- In general, without power is not power, but like a small generator inside the copper wire continuously cutting magnetic lines under the condition of current will produce a certain direction, and the wood is not to produce electricity and friction sparks
- Q:electrical wire prices
- It's merely a coincidence.. The price of OIL and the price of COPPER have been in flux for years... Precisely why in america they want to get rid of the penny... it will soon cost more than a penny to make them. Just imagine if they were solid copper like the old wheat backs.
- Q:Hello,I'm trying to replace my old ceiling fan with a new one but i can't seem to figure out the wiring.I have three wires coming out of the ceiling: 1) Two white ones that were connected together when the old ceiling fan was installed2) A grey wireI have four wires in the new fan:1) Black2) Black and White (would connect with the black based on the instructions)3) Green Grounding4) WhiteCan you help me figure out the connections. Thanks!
- I wish contractors followed the wiring / building codes. The white wires are neutral wires that return the circuit back to the panel. Grey? where in the world did that come from BUT I have to assume that it's the hot wire from the panel. Black black with the white tracer to your grey wire. White to the white if at all possiable put a screw in the box with the green wire or at least wrap it around the screw from the horseshoe that you are putting in the box. Be sure that the switch is off. If it's wired properly there will be no hot wire in the ceiling box. The hot is open at the switch. That's why the light doesn't turn on. Follow me?
- Q:Question about the 3.5mm cable, I cut it open and there are 4 individual wires inside of it. I've only ever seen 2 wires and a loose one. Which ones are right/left and would the other 2 both be ground?The colors are red/green/white/black. I'm assuming the red/white are right left like normal? But I'm not too sure.
- yeah audio cable..
- Q:How can I investigate the resistance of wire and how it changes with the length of the wireCheers
- If you don't have a multimeter, you can probably see the effect of resistance with a flashlight bulb and a small battery (AA or AAA, etc). Get a spool of wire, needs to be coated/insulated wire. Connect the bulb to the battery with the shortest wire possible. See how bright the bulb is. Then, connect again using the entire spool of wire (hopefully you can get at both ends of the wire while it is still on the spool). The bulb will be dimmer because the voltage at the bulb will be reduced by the resistance of the wire (resistivity per unit length X the length of wire). If the length of wire on the spool is too long, the bulb will not light up at all.
- Q:just bought a brinks indoor motion sensor switch and having problems installing. the regular light switch has 2 black wires that was connected to one end and a red to the other. the white wires in the wall are already together. the motion sensor switch has black, blue, red wires and its ground wire. the instructions says not to use the red wire for single switch so confused on how to wire them.
- It sounds like the existing setup is a three-way - meaning that there are two switches that control the same light? If so, you need to know which of the black wires on the existing switch is the hot wire - the other two are known as travelers. Look at the existing switch again, is one of the screws a slightly different color form the other two screws? That's your hot wire. Or the red and one black are on one side of the switch and the other black is on the opposite side - the one that's on it's own side is often the hot wire. Hook the motion sensor switch's black to the hot wire, blue to a traveler, red to the other traveler.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Heavy Galvanized Wire
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches