Heavily Galvanized Wire

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Hot Dip Galvanized Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

(7) Zinc Coating

Meet GB/T 15393 standard.

Q: has black wires.: Two black wires in the box would be a hot from the supply and a switched hot to the load. If the timer has only two wires then it should be pretty easy to just connect them. If they are marked line and load then you would have to hook the wire for line to the wire in the box that is always hot from the supply and the other to the wire marked load. If you are still unsure then it really is not a job for you alone, enlist the help of someone with a bit more experience or even an electrician.

Q: Okay so I just finished replacing a stolen car radio, but I think I messed up the wiring... When I turn off the car the radio doesn't seem to save the presets I had... it resets the whole stereo... I think it has something to do with the wiring I did... When I installed the radio there were two 12+ volt wires... One said 12+ volt constant and was yellow, and the other said 12+ volt switch and was pink... Problem was when I wired only the yellow one the car stereo wouldn't work, so I tried the pink one and that didn't work.. SO thinking I was clever I wired both to the 12+ volt and VOILA the radio turned on... Problem is I don't think that's how I was supposed to wire it... I have a '97 Honda accord Ex and I don't know if that's what I was supposed to do... :#92;: the yellow wire is supposed to go to constant power. the pink wire is supposed to go to a switchable power source. usually an ACC wire.

Q: I m wondering if there s a Neutral Wire in this picture (yes I turned off the breaker to get this photo). I want to put in a quot;Smart Light Switchand they require a Neutral Wire. I ll have an electrician do the work, but want to make sure the wire exists first.: The neutral is the white wire on the receptacle.

Q: Green (ground), got it.Black (positive), got it.White (common), got it.Gray wire with like a black fiber in it, what is this? This is a pendant light so my guess is its just a filler wire to bulk up the cord it hangs from, am I right?: The gray wire is used as a physical support for the light fixture. You tie each end to the light fixture and to the box where the power wires are connected. This is so that you don't use the power wires as a physical support (hanger) to hold the light in place. Think of a swag lamp from years ago. The lamp hung from a chain connected between the lamp and the ceiling. The power cord never supported the weight of the lamp fixture. The black fiber in the gray wire is a strong cord.

Q: A wire is 1.5 m long and has a diameter of 1.5 mm. The stretch modulus of the wire is 6.2 x 10^10 N/m^2. If a force of 400 N is applied to end of the wire then the increase in length of the wire is???please help, thanks: The stretching of wire by longitudinal force: If F force applied across the crosectional area A of wire of radius r and lenght L then the wire elaogates in the dirextion of force Stress P = F / A A = pi* r^2 = (1.5/2)*10^-3 = 7.5 *10^-4 m^2 strain produced = dL / L = increase in length / original L Young's modulus or elastic (stretch) modulus for the maretial, within elastic limits, Y = stress/strain strain = stress / Y dL = F * L / A * Y = F * L / pi (r^2) * Y dL = 400* 1.5 / 3.14 (7.5 *10^-4)^2 * 6.2*10^10) meter dL = 0.005479 * meter dL = 5.479 millimeters increase in length

Q: Why when you loop a straight wire into loops (coil), it acquires a higher inductance?: Imagine two closely spaced parallel wires. If you run a current through one, it creates a magnetic field that induces current into the second wire, which causes an even stronger magnetic field. Now if you run the same current through both wires, they both create magnetic fields that affect each other. Any two loops in the wire are just like two parallel wires with the same current, both creating magnetic fields that affect each other. So a loop is like a bunch of parallel wires affecting each other.

Q: so im doing a custom buggy and i need so different colored wire im looking for a place to get lots of different colored wire for cheap: Summit Racing...

Q: what are the ground and power wires for a walmart replacement cigarette lighter?: the power wire is usually a colored wire like red,blue. the other wire should be white,green or a bare copper wire.

Q: friend i want litz wire in this wire consits of group of enamled coted copper wire(like machine winding wire with multi lead wire),so i want types different guages(that each lead in wiretotal wire guage) and no of leadds.my pupose is for project wire for with standing wire capcity of 20amp's. please give information............................: www.okorder /

Q: I NEED TO CHECK IF A WIRE IS GOOD ON A FITNESS MACHINE. HOW DO I KNOW IF ITS GOOD? WHAT SHOULD THE OHMS BE?: any wire, unless it is very long or very thin, will measure zero ohms on an ordinary ohmmeter. But check for continuity does not completely check a cable. Most cables have several conductors in them, so you need to check each one end to end, and check resistance between the wires. Between them, it should measure open or infinite ohms. But the cable could still be bad. Tell us the details please. .

Send your message to us

*Email

*TEL

*Quantity

*Unit