Floor Spring for Glass Door/Floor Hinge for Glass Door FS-25
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 100000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
INTRODUCTION
Floor Spring is used for glass door, and they can be used together with door clamp. Floor Spring can be opened with double sizes, and on this point, it is different from that of door closer, which can just be opened by one size. The key of technique lies on the loading seat under the main bearing, which decides the level of loading on the floor spring. Usually it can be opened from 300thousand or 1million times
FEATURES
u Applicable for glass doors, wooden doors and the glass doors of metal frame and wooden frame.
u Floor spring comply to EN 1154 and GB standard , and fire-rated EN1634 standard.
u Maximum 500000 cycles tested without damage or maximum 7 years guarantee.
u Double ways opening with smoothly movement, hold-open at 90°.
u Closing speed and latching speed adjustable, latching point accurately at 0°
u Stainless steel cover plate, satin or mirror surface available.
u High quality casting iron floor spring body with 2 layers anti-rust coating.
u All spindle types available for different countries.
u Germany hydraulic machine oil and sealed rings, keep perfect working in cold temperature.
SPECIFICATION
INSTALLATION STEPS
1. Draw lines and make floor spring pivot center and door-nip pivot coincide with each other.
2. Drill holes on the floor according to the instructions. The sizes of the holes must tightly match the floor spring.
3. Place the floor spring into the holes and position it.
4. Raise the door leaf installed with door-nip, and insert the floor spring pivot into the hole of the door leaf.
5. Adjust the screws at three directions. Make them vertical and the upper and lower pivot center coincide with each other.
6. Adjust the speed of door closing.
7. Put the decoration cover on the floor spring.
Package
Workshop
Testing Room
- Q:What kind of spring has the best performance?
- Spring verticality, verticality is bad, will directly affect the strength and life.
- Q:What kind of production equipment does spring factory usually have?
- Multi function forming machine, coil spring machine, 580 press spring machine, extension spring machine, etc.Small heat treatment is also needed
- Q:What are the categories of springs?
- A compression spring is spring under axial pressure, the material section in which are round, rectangular and is also useful multi strand steel rayon coiled spring, generally for pitch, compression spring shapes: cylindrical, conical, convex and concave and a small amount of non circular, will there is a certain gap between the ring and the ring compression spring, when subjected to external load when the spring contraction deformation, deformation energy storage.
- Q:Buffer spring buffer for automobile
- Rubber buffer also known as buffer, buffer, buffer block, rubber shock absorber, shock absorber rubber and so on, the most correct name is "automobile spring cushion", is the name of Car Spring Buffer Retainer English, 1 luxury cars with a buffer principle significantly improve the damping performance of vehicles.
- Q:How to distinguish between spring steel and stainless steel
- Stainless acid resistant steel, or stainless steel, is made up of two parts: stainless steel and acid resistant steel. In short, steel that resists atmospheric corrosion is called stainless steel, and steel resistant to chemical corrosion is called acid resistant steel. Spring steel is a quality carbon steel, but it can rust.
- Q:What is spring pressure and height?
- That is, the spring is compressed to the height of the full circle.
- Q:The glass door spring is broken. How much would it cost to change it?
- 60-100, you don't have to listen to them to buy too expensive
- Q:What is flat steel? Plain carbon flat steel? Spring flat steel
- Section steel is one of the four major steel products (plate, tube, mould, wire). According to the section shape, the section steel is divided into simple section steel and complex section steel (deformed steel). The former refers to the steel, round steel, flat steel, angle steel, six angle steel; the latter refers to the I-beam, channel steel, steel, steel, steel frame bending etc.. Square, square section steel, cold and hot points in two; length of hot-rolled square steel 5-250mm; cold drawn steel length 3-100mm. Round - round section steel, hot, forged and drawn three, hot-rolled bar diameter 5-250mm, which 5-9mm used as drawing steel wire material, called wire; due to disk supply is also called hot rod. Forged round steel is thicker, used as axle billet. Cold drawn round steel diameter 3-100 mm, high dimensional accuracy. Flat - width 12-300mm, thickness 4-60mm, cross section is rectangular and with pure edge of steel. Flat steel can be finished steel, or can be used as the blank of welded pipe and thin slab for laminated sheet rolling. Angle steel -- two kinds of grade angle steel and unequal angle steel. The dimension of angle iron is expressed by the dimension of the length of side and the thickness of edge. The standard angle steel, usually produced, is 2-20, which is the centimeter side length. Such as 5 equal angles, that is, the length of 5cm (50mm) angle steel. The same horn steel often has 2-7 different edge thickness. Steel bars are not the classification of profiled steel. First, the basic concepts of ferrous metals, steels and nonferrous metals are briefly introduced before introducing the classification of steels, ferrous metals, steels, and nonferrous metals. 1. Ferrous metals are alloys of iron and iron. Such as steel, pig iron, iron alloy, cast iron and so on. Steel and pig iron are both...
- Q:In short, in vibration and wave, it is not easy to make mistakes when we grasp the difference and relationship between "displacement" and "displacement relative to the balance position"
- In short, in vibration and wave, it is not easy to make mistakes when we grasp the difference and relationship between "displacement" and "displacement relative to the balance position"
- Q:Physics high school. Why does a spring fall to the lowest point and the acceleration a must be greater than the acceleration of gravity g ah. Seek expert
- Is the map tilted?.Look at the picture. It means that a naturally stretched spring is placed vertically and then put a mass of m at zero initial speed.If dropped to the lowest point, the speed of the object v=0, object by the acceleration of gravity g down, if not spring to give it an g greater than or equal to the acceleration, the object will continue to fall, do not conform to the original intention of "low".So the acceleration inside the spring must be greater than or equal to g.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Floor Spring for Glass Door/Floor Hinge for Glass Door FS-25
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 100000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords