Glass Door Floor Hinge/ Door Closer/Floor Spring for Glass Door/Floor Hinge for Glass Door FS-533
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 100000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
INTRODUCTION
Floor Spring is used for glass door, and they can be used together with door clamp. Floor Spring can be opened with double sizes, and on this point, it is different from that of door closer, which can just be opened by one size. The key of technique lies on the loading seat under the main bearing, which decides the level of loading on the floor spring. Usually it can be opened from 300thousand or 1million times
FEATURES
u Applicable for glass doors, wooden doors and the glass doors of metal frame and wooden frame.
u Floor spring comply to EN 1154 and GB standard , and fire-rated EN1634 standard.
u Maximum 500000 cycles tested without damage or maximum 7 years guarantee.
u Double ways opening with smoothly movement, hold-open at 90°.
u Closing speed and latching speed adjustable, latching point accurately at 0°
u Stainless steel cover plate, satin or mirror surface available.
u High quality casting iron floor spring body with 2 layers anti-rust coating.
u All spindle types available for different countries.
u Germany hydraulic machine oil and sealed rings, keep perfect working in cold temperature.
SPECIFICATION
INSTALLATION STEPS
1. Draw lines and make floor spring pivot center and door-nip pivot coincide with each other.
2. Drill holes on the floor according to the instructions. The sizes of the holes must tightly match the floor spring.
3. Place the floor spring into the holes and position it.
4. Raise the door leaf installed with door-nip, and insert the floor spring pivot into the hole of the door leaf.
5. Adjust the screws at three directions. Make them vertical and the upper and lower pivot center coincide with each other.
6. Adjust the speed of door closing.
7. Put the decoration cover on the floor spring.
Package
Workshop
Testing Room
- Q:How should we choose the spring material?
- In the small spring should be used after hardening spring steel wire, cold drawn steel wire and lead bath oil tempered steel wire with high strength and good surface quality, fatigue performance is higher than the ordinary tempered steel wire, simple processing, good manufacturability, quality and stability.
- Q:Is spring steel manganese steel?
- The most important characteristic of manganese steel is that it can be worked hard under strong impact and extrusion, and its wear resistance is improved, mainly by its working hardening.Spring steel mainly requires large elasticity, high yield strength, and can withstand repeated load without breaking. Spring steel only after heat treatment (quenching + medium temperature tempering) can show its high elasticity, that is, after a certain load, does not occur permanent deformation. The content of Mn in spring steel is much lower than that of Mn in manganese steel.
- Q:What kind of spring has the best performance?
- Spring surface scars, spring surface injury to use a magnifying glass to see, manufacturers generally use 300 times electronic magnifying glass, spring 300 times, see the injury, the impact on life is very big.
- Q:Is the car short spring good?
- The factory is a hydraulic cylinder, and the damping force and the length of the expansion are matched with the length of the spring and the telescopic distance. Instead of changing the short spring will increase the load of the original vehicle hydraulic shock absorber, shock quickly destroy.
- Q:What is spring pressure and height?
- That is, the spring is compressed to the height of the full circle.
- Q:How to choose spring steel material?
- Spring steel is selected on the basis of the section size of the spring, such as high carbon steel 65, suitable for production in the spring of 12 ~ 15mm under section 60CrMnA, suitable for the production of spring and the car less than 50mm in diameter with heavy-duty spring. The 30W4Cr2VA is used to make heat-resistant spring for work below 500 degrees centigrade. Generally, hot forming springs are generally quenched and tempered at moderate temperature to obtain a structure with a maximum elastic limit and fatigue properties
- Q:What is an independent bagged spring?
- Independent bagged spring is a spring with non-woven package, barrel type design can prevent the spring friction and swinging or noise, no influence between spring, elastic energy in accordance with the size of individual expansion, different weight average and proper support of various parts of the body to keep the spine straight, make sleep more comfortable. Bagged spring than ordinary spring production process is more complicated, the cost is higher, so the price is slightly expensive. But human health is obviously.
- Q:The glass door spring is broken. How much would it cost to change it?
- 60-100, you don't have to listen to them to buy too expensive
- Q:What is flat steel? Plain carbon flat steel? Spring flat steel
- It is the name of a steel produced according to a certain specification, such as angle steel, channel steel, etc. ordinary carbon flat steel and spring flat steel are different materials used to make flat steel
- Q:Hydraulic diagram of the one-way valve has two kinds of drawing, with a spring, without a spring, what is the difference between automatic reset function is not? Without a spring, it will not be repeated
- General one-way valve is spring to reset, as for drawing may be the standard of drawing is not the same. As long as no oil passes, it closes.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Glass Door Floor Hinge/ Door Closer/Floor Spring for Glass Door/Floor Hinge for Glass Door FS-533
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 100000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords