Glass Door Floor Spring/Floor Hinge for Glass Door FS-65
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 100000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
INTRODUCTION
Floor Spring is used for glass door, and they can be used together with door clamp. Floor Spring can be opened with double sizes, and on this point, it is different from that of door closer, which can just be opened by one size. The key of technique lies on the loading seat under the main bearing, which decides the level of loading on the floor spring. Usually it can be opened from 300thousand or 1million times
FEATURES
u Applicable for glass doors, wooden doors and the glass doors of metal frame and wooden frame.
u Floor spring comply to EN 1154 and GB standard , and fire-rated EN1634 standard.
u Maximum 500000 cycles tested without damage or maximum 7 years guarantee.
u Double ways opening with smoothly movement, hold-open at 90°.
u Closing speed and latching speed adjustable, latching point accurately at 0°
u Stainless steel cover plate, satin or mirror surface available.
u High quality casting iron floor spring body with 2 layers anti-rust coating.
u All spindle types available for different countries.
u Germany hydraulic machine oil and sealed rings, keep perfect working in cold temperature.
SPECIFICATION
INSTALLATION STEPS
1. Draw lines and make floor spring pivot center and door-nip pivot coincide with each other.
2. Drill holes on the floor according to the instructions. The sizes of the holes must tightly match the floor spring.
3. Place the floor spring into the holes and position it.
4. Raise the door leaf installed with door-nip, and insert the floor spring pivot into the hole of the door leaf.
5. Adjust the screws at three directions. Make them vertical and the upper and lower pivot center coincide with each other.
6. Adjust the speed of door closing.
7. Put the decoration cover on the floor spring.
- Q: Buffer spring buffer for automobile
- The automobile spring buffer (cushion glue) is a kind of rubber product with high elasticity and high tenacity. It belongs to the automobile refitting parts. The utility model is used for installing the spiral spring of an automobile suspension system, and mainly acts as a buffer shock absorber and protects the shock absorber. This function is a physical function.The buffer is made of an open circular ring with a groove (for holding a coil spring), with two, three or more holes on each side. According to the standard specification of the spring spacing, the buffer rubber is divided into seven standard models: A+A, A, B, C, D, E and F. In theory, these seven models can cover the world's largest part of the spiral spring shock absorbers required.
- Q: What kind of production equipment does spring factory usually have?
- Multi function forming machine, coil spring machine, 580 press spring machine, extension spring machine, etc.
- Q: What is flat steel? Plain carbon flat steel? Spring flat steel
- Flat steel, also called flat steel strip, is a long thin steel with a rectangular cross-section. According to the production process, it can be divided into hot rolled flat steel strip, fine shearing flat steel belt and cold drawn flat steel belt.Ordinary carbon flat steel - the component is ordinary carbon structural steel, suitable for wide range.Flat spring - flat steel used for making spring plates of automobiles, containing manganese.
- Q: How to choose spring steel material?
- Whether the spring is good or not is of great importance to the choice of the spring material. In general, selection of spring material, should take into account the load properties, spring force, various factors should be size, working conditions and price, etc..
- Q: What kind of spring has the best performance?
- Spring surface scars, spring surface injury to use a magnifying glass to see, manufacturers generally use 300 times electronic magnifying glass, spring 300 times, see the injury, the impact on life is very big.
- Q: How should we choose the spring material?
- Whether the spring is good or not is of great importance to the choice of the spring material. In general, selection of spring material, should take into account the load properties, spring force, various factors should be size, working conditions and price, etc.. Specific can follow the following principles: 1) in determining the shape and size of spring material, should be preferred dimensions behind national standards or standard stipulated, try to avoid using non standard materials. Although the spiral spring square or rectangular cross section material, the elastic deformation can be higher than, can make the small volume of the spring, for spring, in small space or under impact load but because of square or rectangular section material shortage, the price is higher, and the spring forming is difficult, so should be avoided. Ring section spring material diameter series see table 3-9. 2) the degree of cold plastic deformation of cold drawn spring materials is high. Most finished steel wires have reached the required mechanical properties when they leave the factory. The surface quality of the steel wire is high, and the manufacturing process of the spring is simple. For springs of medium or small spring or high fatigue life, the cold spring or cold drawn spring or steel wire or strip shall be selected as far as possible. Carbon spring steel wire (group I, group II, group II A, dish group) and important uses of 65Mn spring steel wire during the cold drawing process caused in large residual stress, the larger the size change after low temperature tempering, and thus affect the dimensional accuracy of the spring. For the bending radius of smaller tension and torsion spring, as well as smaller steel wire compression...
- Q: Is the car short spring good?
- Hello! General short spring is not short, but also hard, short effect is to reduce the body, lower center of gravity, hard role is to reduce the body tilt in vehicle cornering, turn faster. The disadvantage is that the chassis is low, through the poor sex, easy to drag the site, hard on the comfort of the.
- Q: How about the size of the elasticity?
- Stretch by the object, extrusion and elastic deformation, the elastic solution is to look at the state of the object, at rest or in uniform linear motion of an object according to the stress analysis of the relationship between the force and other force, curve movement or acceleration force balance objects can analyze the stress in Newton's second law for, no matter what type of stretch can use the two methods to solve the hope to adopt: -)
- Q: The glass door spring is broken. How much would it cost to change it?
- Replace the ground spring, the price of the earth spring itself, but also part of the labor costs, after all, it is very expensive. Land springs in general, if used in general, that is, about 150, but with labor costs, usually around 80. Specific prices should be based on your actual situation, you and the master speak.
- Q: Physics high school. Why does a spring fall to the lowest point and the acceleration a must be greater than the acceleration of gravity g ah. Seek expert
- According to the conservation of mechanical energy, the object should be a free fall motion at the upper end of the spring
Send your message to us
Glass Door Floor Spring/Floor Hinge for Glass Door FS-65
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 100000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
