fiber cement panel
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 120000pcs pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1,LUTAI Fiber cement board is a stable performance and light weight building &decoration board used cement as major and natural reinforced, with the process of pulping,emulsion,forming,pressurization,autoclaving,
drying and surface treatment.
Thickness : 4.5mm-30mm
Size :1200*2400mm, 1220*2440mm, any size that u need .
Surface : 40#-120# sanding surface , polished surface , tapered edge .
2,Product characteristics :
Density : 1.2-1.5G/CM3
Fire-proof Rate : A-Class incombustible (GB8624-1997)
Incombustibility(min): 240 minutes (GB/T9978-1999)
Water content : ≤30% Swelling ratio: ≤0.4%
Anti-bending Strength: ≥16MPA Frost resistance : Don’t appear cracking and delamination after 25 cycles of freezing and thawing . (GB/T7019-1997)
Radioactivity: standard of GB6566-2001 (A-class Decoration Materials)3,Recommed application:
Partition board , exterior wall cladding , panel, suspended ceilings ,lightweight grouting panel, interior dry wall decoration board ,interior wall after painting and coating .
- Q: Can cement board be used for floor decoration?
- A floor of the ground used: 1. tiles 2. flooring 3. marble you asked the shop where the shop shop black stone was here I tell you about my decoration experience, the store floor decoration generally use ordinary rows of tiles, The reason is: all ceramic tiles and marble cost is expensive, the general owner will not use
- Q: Installing tile in my laundry room. put down the cement board with a mortar/thin set base under it, then nailed it down according to manufacturer's instructions. The mortar/thin set totally dried then I had to do a few loads of laundry before I was able to put any tile down. Unfortunately one of the hoses hooked up to the washer leaked and soaked the cement board and I'm sure also the sub-floor. Do I need to rip out the cement board and re install before I install the tile? obviously I would need to ensure the floor is fully dry before I install the tile. Thanks
- You shouldn't have to rip it out. I would let a fan run on it for a few hours just to make sure it is totally dry.
- Q: I bought some plaster which is to be used for a wall stenciling project. Is this type plaster ok to use to stick tiles on the kitchen wall as well? I PLAN TO REMOVE THE TILES WHEN WE MOVE, so thought this type of plaster may--or probably will be easy to work with when removing the tiles later in a year or two? Please advise, thanks
- It okorder You should be just fine!
- Q: We have drywall in our kitchen that was painted with a smooth semi-gloss paint a good 8 yrs ago. We'd like to install 3x6 tumbled marble as a backsplash over the drywall. It's about 1/4 thick so probably slightly heavier than say, the tiny square glass tiles that come on a 12x12 netting. One person at the Home Depot said we could just sand and scrape up the drywall and then apply the thinset and install the marble. Another said we might want to use a cement backing. We aren't really DIYers and would so we don't want to create extra work with the cement backing if it isn't needed. That said, we don't want the drywall to start peeling and the marble tiles to start falling off after a short amount of time. Please advise. Thank you!
- ild install a 1/4' hardyboard board first -the thinset will not last sticking the tiles to the paint
- Q: where can i buy national gypsum perma base cement board?
- Go to cshopping
- Q: What is the cement pressure plate?
- With light, high strength, waterproof, anti-corrosion, fire, large format, good processing, improve construction efficiency and so on. Widely used in civil and industrial buildings. Can be used for building floor, interior wall panels, exterior panels, ceiling panels, curtain wall panels, composite wall panels, insulation materials, roofing and other parts.
- Q: Bent cement board while installing onto floor...will it be ok?
- well i hope youre not using actual thinset. Thinset is for wall tile :p You want mortar. and 1/4 backerboard would have been plenty, but too late now :p even if the board cracked...assuming you screwed it down well, and mortared underneath it, it's fine. No worries.
- Q: What are the differences between the gypsum board and the cement pressure plate and the Eide board?
- Cement pressure plate is based on natural fibers and cement as raw material, by the pulp, forming, cutting, pressing Steamed into a new type of building plate. With light, high strength, waterproof, anti-corrosion, fire, large format, good processing, improve construction efficiency and so on. Mainly used for internal and external walls, pouring walls, composite panel wall panels, fire door lining, external wall insulation panels.
- Q: do i need mortar under the cement board?
- no just screw or nail good
- Q: Want to do their own cement board, but made out of the color on the white, how can make the cement board color made dark gray
- I suggest you use PC32.5 cement (composite cement), because the cement is mixed with a lot of fly ash so this kind of cement to do the surface color is the deepest, of course, some of the factory with the lighter gray color, then After the cement is condensed, it is also darker than other cement, and some fly ash is grayed out. You buy cement when they look, there is a way to mix cement when they add coal dry stone powder or fly ash, of course, the strength of cement down, so if the choice of the latter should be mixed with their own purchase PO42.5 grade cement to blending, or do out of the cement board strength is too low is not enough. If the composite cement and then mixed with the need to grasp the amount of the problem.
Send your message to us
fiber cement panel
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 120000pcs pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords