Factory Direct Custom Made Double Acting Hydraulic Ram

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1.ISO9001:2008
2.Seal:Merkel or Parker
3.Working pressure:16-25Mpa.
4.10 years of experienc
5.Material:CK45

CMAX series engineering hydraulic Cylinder

(1)working pressure:16MPa

(2)Piston diameter: 40-250mm

(3)Seals:Merkel or Parker

(4)Sensor: MTS or Balluff

Q: What are the characteristics of a piston hydraulic cylinder? How many kinds are there? What are they used for?If anyone knows, just say something: The power of dynamic components of hydraulic cylinder can be relatively large power components, the use of hydraulic system, the 2-- from the medium air is inexhaustible, no cost and supply difficulties, the gas used directly into the atmosphere, convenient. The hydraulic oil in the air, 3-- small viscosity, resistance is less than 4-- but the compression rate of air hydraulic oil is far greater than the hydraulic oil so it work smoothly and in order to better response sent greater output Torque, it is necessary to use the volume. Compared to swing vane motor. Many gear rack swing hydraulic cylinder. The torque is generated and transmitted by a driving gear is provided with a rack piston shaft lateral position achieved. According to the design, roller bearings, hydraulic balance or prop up the shear counterproductive gear tooth and the piston. The principle of swinging cylinder reciprocating movement of the hydraulic cylinder is driven by gear rack, the gear shaft is converted into reverse swing rotation, while the reciprocating cylinder thrust into the output torque of the gear shaft. The gear shaft is proportional to the swing angle and the length of the rack, so the gear shaft swing the angle can be arbitrarily selected, and greater than 360 degrees.

Q: What is a constant velocity cylinder? What's the difference between a hydraulic cylinder and a hydraulic cylinder?: The cylinder piston rod extends out should be constant and consistent back speed cylinder called isokinetic cylinder. The difference between it and ordinary hydraulic cylinder hydraulic cylinder is common only a head with a piston rod extends out of the general slow recovery fast, because the relationship between the effective area of the piston cavity.

Q: What is the working pressure of the hydraulic cylinder with a diameter of 80?: I think you should ask about how much work you can do at work. Formula: theoretical output = work pressure x piston area. The piston area 80 cylinder diameter is 3.14*40*40=5026mm^2; if the work pressure is 10MPa; then the theoretical output is 5026x10=50260N, equivalent to 5 tons of force.

Q: What are the acceptance criteria for hydraulic cylinders?: China has published the hydraulic cylinder of the ISO standard (excluding seal standard 6), there are more than 20, as follows: ISO3320-75 hydraulic and pneumatic systems and components of a cylinder diameter and piston rod diameter of a ISO3321-75 metric series of hydraulic and pneumatic systems and components of a cylinder bore and piston rod diameter ISO3322-75 Inch series of hydraulic and pneumatic systems and components of a cylinder of a nominal pressure ISO4393-78 of hydraulic and pneumatic systems and components with a cylinder and a piston stroke basic pressure ISO4394-78 hydraulic and pneumatic systems and components of a cylinder diameter steel pipe processing conditions of ISO4395-78 hydraulic and pneumatic systems and components of a cylinder and a piston rod thread size ISO5597/1-80 type of hydraulic cylinder piston rod and a piston reciprocating sealing groove: Nominal dimensions and tolerances of 1 series ISO6020/1-81 -160bar series hydraulic single rod hydraulic cylinder - Mounting dimensions

Q: The surface of the hydraulic rod is chromium, and it often causes strain, scratch, electric shock and so on. The routine method is slow to repair and the effect is not satisfactory. Don't want to play with copper, also do not want to use cold, patch method, because of poor adhesion, never long broken. Is there a better way to fix it?: Brush plating method to repair hydraulic rod, cylinder pull, the best effect. Because the 1. can be repaired on the spot, the trouble of loading and transporting is avoided. 2., coating adhesion is good, no obvious boundaries, repair surface hardness, good wear resistance. 3. low temperature operation will not change the properties of the substrate. Electroplating repair technology is a kind of traditional repair technology to restore the size of parts at low temperature.

Q: Can the cylinder be hydraulic?: Conclusion: the cylinder can give off.Conditions: 1, cylinder skill quality can not be too much of the time, so the cylinder was originally a little hit oil spill will become.

Q: Urgent, how, on the mechanical hydraulic buffer for a large amount? What mechanical pneumatic elements are used?: The question is too general.Look for the same industry, large enterprises, in their website will be classified according to industry applications, check will be more convincing.

Q: Hydraulic principle: Hydraulic transmission is also called volume hydraulic transmission, is liquid as the medium, the transmission device to transmit energy and control the use of liquid pressure energy and kinetic energy. Usually the liquid medium using the hydraulic system with the remaining liquid pressure energy is called hydraulic oil.

Q: What are the components of the cylinder and the hydraulic cylinder?: Hello, are you asking about the cylinders and cylinders? Cylinder barrel, upper and lower end cover, pull rod, sealing ring and so on. I am a professional, do this, what problems can continue to ask me?

Q: Is the hydraulic cylinder at rated pressure the greater the stroke and the greater the pressure, is there a formula?: Bore diameter: hydraulic cylinder jacket, unit mm;Hydraulic pressure: hydraulic system to provide the maximum hydraulic pressure, unit MPa * 10.Such as:If the bore 280mm, hydraulic pressure of 25 MPa, then the cylinder thrust3.14 * (28 / 2) x 2 (25 x 10) / 1000=153.86 (ton)

Send your message to us

*Email

*TEL

*Quantity

*Unit