telescopic dump truck hydraulic cylinder 2014

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1.ISO9001:2008
2.Seal:Merkel or Parker
3.Working pressure:16-25Mpa.
4.10 years of experienc
5.Material:CK45

CMAX series engineering hydraulic Cylinder

(1)working pressure:16MPa

(2)Piston diameter: 40-250mm

(3)Seals:Merkel or Parker

(4)Sensor: MTS or Balluff

Q: Hydraulic oil? Refrigerant? Brake night? What are they? What's the function of it?: Most of the use of hydraulic oil in the hydraulic cylinder, like excavators and forklifts, hydraulic cylinder like muscles, the engine compressor, the compressor of the hydraulic oil to the oil into the hydraulic cylinder lifting hydraulic cylinder through the refrigerant tubing, you say is the refrigerator refrigerant? Refrigerator is freon, can be recycled, if the leakage of fluoride, of course, will have to repair fluoride, brake night is what things do not know

Q: How do I calculate the flow rate of the hydraulic cylinder?: Hydraulic cylinder flow = hydraulic cylinder piston cross section * speedFor example: the cylinder speed of D10cm requires 10cm per secondThe hydraulic cylinder piston cross-section =pi * D * D, 4=3.14 * 10 * 10 4=78.5 / cm2Flow per second =78.5 * 10=785 ml =0.785 litersThe flow rate is =0.785 * 60=47.1 liters per minute

Q: What is the pivot shaft in the cylinder?: 1. Welding with high strength WE600 welding rod.2, WE600 is a low heat output, suitable for special nickel chromium alloy steel electrode welded all-round, universal design is extremely wide, the general strength of parent materials with high strength, excellent welding performance, stable arc, beautiful shape of seam, in oil, water and rust conditions can welding effect is excellent, can the welding of different steel.

Q: What are the characteristics of a piston hydraulic cylinder? How many kinds are there? What are they used for?If anyone knows, just say something: The power of dynamic components of hydraulic cylinder can be relatively large power components, the use of hydraulic system, the 2-- from the medium air is inexhaustible, no cost and supply difficulties, the gas used directly into the atmosphere, convenient. The hydraulic oil in the air, 3-- small viscosity, resistance is less than 4-- but the compression rate of air hydraulic oil is far greater than the hydraulic oil so it work smoothly and in order to better response sent greater output Torque, it is necessary to use the volume. Compared to swing vane motor. Many gear rack swing hydraulic cylinder. The torque is generated and transmitted by a driving gear is provided with a rack piston shaft lateral position achieved. According to the design, roller bearings, hydraulic balance or prop up the shear counterproductive gear tooth and the piston. The principle of swinging cylinder reciprocating movement of the hydraulic cylinder is driven by gear rack, the gear shaft is converted into reverse swing rotation, while the reciprocating cylinder thrust into the output torque of the gear shaft. The gear shaft is proportional to the swing angle and the length of the rack, so the gear shaft swing the angle can be arbitrarily selected, and greater than 360 degrees.

Q: One hundred1: cylinder 150D-71x-102: cylinder GTD-80/090-P17M3: cylinder XQGA125*160-CA4: hydraulic cylinder COA3110715.035: cylinder MAB125-165P6: hydraulic cylinder SCI80/56 H1765XV980YPSX7: hydraulic cylinder CA100*70*350T8: hydraulic cylinder COA3112458.029: pneumatic gate valve cylinder DN600I need to find each cylinder bore. Stroke. The diameter of the piston rod installation. Pressure rating!!!Urgent need for support for the master! Thank you！！！ (the more specific, the more important.)What's the form? Do not understand.. can not point out in detail...: Where did you get the specifications for each cylinder? Just look for a sample of the brand, and you can see the parameters you need!!! Otherwise, there is no way! Moreover, you can see, you do not write a lot of specifications! So, you still need..... Ha-ha！

Q: Is the hydraulic cylinder or pneumatic cylinder good, their respective advantages?: The hydraulic operation is stable, the output power is large and the cost is high. The air pressure is fast, the output force is small, and the cost is low.

Q: Pneumatic cylinder stem can replace pneumatic hydraulic jacking rod. Who is big?: First of all, to understand your question is..:Can the top rod of the pneumatic cylinder piston rod instead of the piston rod of the hydraulic cylinder? That lever has a lot of thrust?" How is that right?Answer as followsThe top rod of a pneumatic cylinder piston rod can not replace the top rod of a hydraulic cylinder piston rod.

Q: Why is the digital hydraulic cylinder not widely used?: 2, hydraulic system plus flow flow valve; 3, do synchronous cylinder.

Q: Hydraulic shock absorbers and hydraulic buffers are the same thing?: Through the application of a new design, this feature is the use of Iglidur RN56 as the core component, can meet the technical requirements and significantly reduce costs. In this solution, the piston and the sliding bearing at the bottom of the damper are combined in an injection molding assembly.

Q: Apart from the way they are installed, are their sensors universal? That is, can the induction switches used on the A model cylinder be used on the B model cylinders?!Some cylinders use large ones, but others are very small. Are they interchangeable? That is, if the big induction switch is broken, can it be replaced with a small one?: Are you talking about the magnetic induction switch, only the cylinder with magnetic band can be used?

Send your message to us

*Email

*TEL

*Quantity

*Unit