F-KB094 Carbonized bamboo knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
product name：rubber wood knife seat
material：Carbonized bamboo
N.W.：4.636kg
MEAS：38.5*27*12cm
Product advantage：
How does the bamboo product carbonize？Firstly，put the bamboo or bamboo bag into the high-pressure carbonized boiler of 200 degrees - 300 degrees for vapor carbonization.
And after high temperature and high pressure, so that form a hard carbide particles layer on the surface.At the same time,the bamboo itself will be more harder.
The advantage of carbonized bamboo knife seat:after carbonize,hard carbide particles will form a environment not easy living for bacteria on the surface of bamboo product to achieve the antibacterial effect.
At the same time, because after carbonization the bamboo will be more hard than ordinary paper products, preventing wearing and bamboo thorn problem.
Carbonized bamboo knife seat quantity：
Safety, health, bright color，durable，the everyday necessary good products
Anti-mildew change，anti moth
Environmental protection，no crack，no decay
- Q: The system is a wide number of 980TDb, lathe is the Yunnan machine tool factory. Whether it is a manual tool change or MDI way to enter the specified number of knives, the tool holder always turn around, until the emergence of PLC alarm 1000 change knife time is too long, A0000.0 knife can not reach the designated position. What the problem ah, I did not move the parameters of the machine, ah, this morning is good, work in the afternoon a boot on this.Back to the origin of the machine are abnormal, and can not return to the origin of the machine. Press the corresponding button after the machine does not respond, will not act. It's normal in the morning.
- I have encountered such a problem, the circuit has a capacitor breakdown, check the replacement can be.
- Q: CNC lathe turret, sometimes why turn around.
- Open the end of the tool holder, there is a bad disk or water. The solution uses the hair dryer to dry, if it is not OK to replace.
- Q: To the signal line where the pull resistance, pull resistance to do with the trouble to say clearly?
- The pull-up is to position the uncertain signal through a resistor at the high level! Resistive current limiting! Pull empathy!L pull-up is the injection current to the deviceL is weak, but the resistance of the pull-up resistor is differentFor non L (collector or drain) open circuit output circuit (such as the common gate circuit of current and voltage increase) ability is limited, the pull-up resistor is the main function of the open circuit output current output channel for collector
- Q: How can we remove the NC turret
- This is not more than the ordinary lathe CNC lathe, if so simple to take out, it is difficult to achieve automatic change
- Q: Who has any good method or fixture drawings and pictures for younger brother to learn ah, do not be grateful, want to do, but I have not seen this thing, the idea does not come out
- In order to install the taper shank drill, you need to buy or process a tooling, the taper of the inner hole 1:16, the size of the outer circle is determined by the hole of the boring tool holder on your lathe.
- Q: In front of the turret with rear turret in the car to count the G41G42 cutter compensation when there is no difference?
- The turret of the numerical control lathe is the front knife holder in the operator's side.The common lathe is the rear cutter.When the tool head, the G42 tip radius compensation right bias in the car when the hole, when the car is round with G41.
- Q: Is the plastic knife holder of roller skate good or metal knife holder good?
- Each has its advantages and disadvantages, the plastic is relatively light but easy to change and no way to replace, although the metal sink, but more than a ban and can change the knife.
- Q: CNC lathe tool holder clamping bit how to clip
- If it is turret turret, machine tool manufacturers with drill sets, you can directly install straight shank drill, but the specification is not complete.
- Q: The direction of the tool head and the tool head of the NC lathe
- G41g42 use the judgment of the tool tip is not the same as you this figure to 09 knife point for the center of the rotation of 180 degrees is the rear tool head position input value evaluation standard front and rear is the same as the input value
- Q: The rotary tool holder is marked with the knife number. How to define the knife number?
- There is no knife in the actual sense of the knife number, because it is to use the knife to determine the use of the.
Send your message to us
F-KB094 Carbonized bamboo knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
