F-KB090 Carbonized bamboo knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
product name：rubber wood knife seat
material：Carbonized bamboo
N.W.：0.486kg
MEAS：14*16*8cm
Product advantage：
How does the bamboo product carbonize？Firstly，put the bamboo or bamboo bag into the high-pressure carbonized boiler of 200 degrees - 300 degrees for vapor carbonization.
And after high temperature and high pressure, so that form a hard carbide particles layer on the surface.At the same time,the bamboo itself will be more harder.
The advantage of carbonized bamboo knife seat:after carbonize,hard carbide particles will form a environment not easy living for bacteria on the surface of bamboo product to achieve the antibacterial effect.
At the same time, because after carbonization the bamboo will be more hard than ordinary paper products, preventing wearing and bamboo thorn problem.
Carbonized bamboo knife seat quantity：
Safety, health, bright color，durable，the everyday necessary good products
Anti-mildew change，anti moth
Environmental protection，no crack，no decay
- Q: The system is a wide number of 980TDb, lathe is the Yunnan machine tool factory. Whether it is a manual tool change or MDI way to enter the specified number of knives, the tool holder always turn around, until the emergence of PLC alarm 1000 change knife time is too long, A0000.0 knife can not reach the designated position. What the problem ah, I did not move the parameters of the machine, ah, this morning is good, work in the afternoon a boot on this.Back to the origin of the machine are abnormal, and can not return to the origin of the machine. Press the corresponding button after the machine does not respond, will not act. It's normal in the morning.
- I have encountered such a problem, the circuit has a capacitor breakdown, check the replacement can be.
- Q: How to distinguish the CNC lathe turret and turret turret after that car, belonging to the front tool or tool? Before the turret is cylindrical with G42 or inner circle?
- Whether NC or normal car, a knife in the side is the pre processor, or post, either rear or front, when processing with radius compensation are determined according to the post, the outer circle with G42, G41 in the hole.
- Q: In front of the turret with rear turret in the car to count the G41G42 cutter compensation when there is no difference?
- The turret of the numerical control lathe is the front knife holder in the operator's side. The common lathe is the rear cutter. When the tool head, the G42 tip radius compensation right bias in the car when the hole, when the car is round with G41.
- Q: How to maintain the lathe tool holder
- If the positioning and clamping action is normal, the push rod 11 is in contact with the corresponding contact 12, and the signal is sent to indicate that the tool changing process has ended, and the cutting process can be carried out.In addition to the positioning of the hydraulic cylinder and the positioning pin, the motor can also be used to drive the clutch to locate, as well as other indexing and positioning mechanisms.
- Q: CNC lathe tool holder clamping bit how to clip
- You can buy a drill chuck, which is an elastic sleeve, can be fitted with a straight shank drill, but also requires a variety of flexible collet
- Q: For what parts of the process, what is the difference between the installation
- The central frame is mainly used for supporting and fixing the shaft parts or strengthening the rigidity.The difference is: the 1 position is different; the center frame of the 2 does not move with the carriage.
- Q: The rotary tool holder is marked with the knife number. How to define the knife number?
- If you put the first row of knives when the address to the address of the first address, you can use T0101 to call your first row of knives, you can also use T0201 to call your first row of knives. So the first four digits in the back of the T in the number of knives on behalf of the address is not in the row of practical significance. After using the knife to determine the use of the knife.
- Q: What are the advantages and disadvantages of CNC lathe turret
- The radial direction (X direction) of the cutter head is to retreat to the operator. The utility model has the advantages that the knife is convenient and the price is cheap; the disadvantage is that there are only four cutter positions.The rear cutter holder is a tool holder which is used for withdrawing the knife from the radial direction to the opposite direction of the operator. The utility model has the advantages that the cutter position is more than the front cutter holder, and the loading and unloading work piece is convenient. The disadvantage is that the price is expensive.
- Q: CNC machine tool can be drilled hole how to center
- Find a good car end cars to X0, change bit
- Q: Fanuc CNC lathe tool holder for maintenance
- The turret to stop sending disc is bad, if you are a Shenyang machine tool equipment, suggest you directly contact the Shenyang machine tool factory sales office to buy the original knife from disk, too many fake goods on the market, the original letter disc type is JX-4 or JX-4W, JX-4B and JX-4BW on the market is full of fake goods, please discern
Send your message to us
F-KB090 Carbonized bamboo knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
