Colorbond Roofing Insulation with Big Bubble Aluminum Foil
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT or L/C
- Min Order Qty:
- 40HQ m²
- Supply Capability:
- 20 Tons Per Week m²/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
1. Specification of Aluminum Foil with Big Bubble
|
STRUCTURE |
ALUMINUM FOIL/BUBBLE/FOAM/BUBBLE/ALUMINUM FOIL |
|
BUBBLE SIZE |
20mm*4mm |
|
THICKNESS |
4mm |
|
WEIGHT |
400g/m2 |
|
WIDTH |
1.25m |
|
REFLECTIVITY |
96-97% |
2. Application of Aluminum Foil with Big Bubble
(1). Building reflective heat, cold and hot water pipe insulation;
(2). refrigerator partition, central air conditioning, regrigerator and household applliancs insulation;
(3). Insulation, sold-absorbing, noise reduction and moisture-prooof insulation in the care, train, refrigerator car, laboratory and other industries;
(4). Special product packaging and refrigerated packing and so on.
3. Packaing and delivery of Aluminum Foil with Big Bubble
Depends on the clients' requirements and the production conditions.
- Q: Sorry, I asked this in the maintenance and repair section, but no luck.Which is better to have in a 2-story home? My last 2-story home was always hotter upstairs than down. (Physics...heat rises)
- the best is more attic isolation so that the heat don't come directly to second floor.
- Q: I know you're not supposed to directly insulate the roof due to the roof getting super heated in the summer, but my walk-in (actually, more like "crawl in") attic is very hot in the summer and very cold in the winter. Is there anything I can do to improve efficiency? I can't help but think I'm wasting a lot of energy just to keep my roof lasting a little longer.
- You can avoid the condensation problem by simply leaving a minimum 2'' gap between the roof and the insulation. You need to fix battens on to the rafters ( at least 2'' from the tiles ) and then fix blanket or rigid insulation tight between them. The battens will maintain the air space. You then need to fix a vapour barrier over the whole thing and finish with plasterboard. No small job to do it properly ! ps you need to check the condition of the roof before you start and fix any loose tiles etc Alternatively, turn the heating up and wear a thicker sweater.
- Q: I do not have extra space on the roof. Roof also tapers to drains at one end of building.
- Nope. The DOW rigid insulation is an R-5/inch. So 4 inches gets you an R-20. Sorry.
- Q: I would like to find foam type tiles for my roof of decking, insulation?
- www.okorder I checked the website I posted by searching 'foam roofing' on google. This link is what I found but there are others... Google it to find your best deal. I think I will spray this stuff under my pier and beam home just to insulate. Thanks for the tip! I can buy this product, apply it myself and cut the cost down to 1/3 or more.
- Q: on a traditional pitched roof construction,where is heat insulation usually provided?
- On the ceiling.Paper side down to help protect against moister.
- Q: How do I adequately insulate my attic roof to make the space a bit more habitable in the winter? The floors to the living area below are already insulated and we have a gable mounted fan which is great in the summer. I am thinking of adding insulation to the roof with baffles underneath for air circulation through the soffit vents. Am I anywhere near an idea that may work?
- What you could do is line inbetween the roof trusses with fibre wool and then fix heavy cardboard sheets over them to keep them in place. Alternatively you could engage the services of a specialist company who will come and strip off your tiles/slates whatever and spray an insulating foam on the inside thus sealing everything in place.
- Q: Hi, I have got a physics question and was just wondering about it.. Can someone pls tell me how does roof insulation work? how is it effective? How does the insulation changes the heat circulation and transfer inside a house?I know that the insulation prevents radiation from the sun and overheating.. but any more details about radiation, convection and conduction of heat pls?
- Well insulation makes a dead air space (air is stagnant). Since the air is not moving the transfer of hot and cold is slowed down considerably. But since you have to create cross ventilation to reduce rotting in wood and the build up of explosive gasses. Its a crap shoot that it even does any good. Radiation is heat so that's covered by the dead air space. Convection is usually not an issue with the cross venting. Also for conduction the insulation should slow it down considerably.
- Q: attic insulation
- Blow in insulation is so easy and cost effective, do it yourself. Machines can be rented at Lowes, HD, etc where you buy the material.
- Q: Finally remembering to do so, before my family and I left the house for approximately 4 hours, I turned off the heat before leaving. When we came home I turned it back on, but was shocked to see that the temperature had dropped 4 degrees in that time. 4 degrees in just under 4 hours seems like a lot of heat loss, does it not? I've seen the insulation in our roof and it's just that sawdust looking stuff spread everywhere. I feel like I'm paying a lot of unnecessary dollars for heating: the air does kick on every hour or two and we keep the thermostat at 68.Is it reasonable for me to talk to my landlord about this problem and getting better insulation in the ceiling, and maybe in the roof? (the master bedroom, on the far corner of the house, is always 2-3 degrees below the rest of the house). Are my expectations to not lose a degree of heat or more per hour unreasonable? Would a typical landlord consider this a problem worth discussing?
- The roof (assume pitched) doesn't need insulating it's above the attic above the ceilings of all the rooms that need 12 inch of mineral wool insulation to stop heat loss (you may have less thickness not all insulation is to the correct standards) Also if as I suspect the walls of your home are timber with shiplap (and not solid brick / cavity walls) they also require insulation top up. From a google search there is state wide Government grants for insulating homes, could be available in your state? using blown insulation to walls/ceilings. If you decide to install it yourself the payback is excellent -in 12 months depending on fuel cost and what existing insulation (from your description minimal) The landlord could be entitled to increase your lease costs if he takes the work on as he has greatly improved the thermal insulation which will reduce your heating costs and make his property more valuable to lease.
- Q: we want to put a model railway up in the loft,and i like the idea of having white plastic cladding throughout up there,my hubby is insulating the roof tomorrow,but he prefers plasterboard,at least the cladding will be maintenance free,
- i think it might be able to pass code if you ever sell the house.i myself would use sheets of white wainscoting.also make sure the insulation if it has a paper backing ,paper faces the room.
We are a well-known enterprise specializing in the production and sales of high-grade meltalized film, foil film, foil foam and other composite product.
Since the establishment of our company, we have been devoted to setting up a good reputation in the world.
1. Manufacturer Overview
| Location | Zhejiang, China |
| Year Established | 2004 |
| Annual Output Value | Above US$ 0.2 billion |
| Main Markets | 20.00% Mid East 15.00% Northern Europe 15.00% North America 12.00% Eastern Asia 10.00% Africa 9.00% Eastern Europe 8.00% Southeast Asia 4.00% Oceania 3.00% Western Europe 2.00% Southern Europe Mid East；South east asia；North America |
| Company Certifications | ISO 9001 |
2. Manufacturer Certificates
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period |
3. Manufacturer Capability
| a) Trade Capacity | |
| Nearest Port | Shanghai |
| Export Percentage | 41% - 50% |
| No.of Employees in Trade Department | 20 People |
| Language Spoken: | English; Chinese |
| b) Factory Information | |
| Factory Size: | Above 100,000 square meters |
| No. of Production Lines | Above 4 |
| Contract Manufacturing | OEM Service Offered; Design Service Offered |
| Product Price Range | Average |
Send your message to us
Colorbond Roofing Insulation with Big Bubble Aluminum Foil
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT or L/C
- Min Order Qty:
- 40HQ m²
- Supply Capability:
- 20 Tons Per Week m²/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
